VADriven.com Forums

Notices
Tech Talk Anything technically related to your vehicle should be posted here. If you're looking to have work done, try one of the Regional Forums.

Need quick answer........should be simple, Honda people inside

Thread Tools
 
Old 07-13-2010, 06:43 PM
  #11  
Shoryuken!
 
Snoop 95's Avatar
 
Join Date: Jul 2008
Posts: 955
Likes: 0
Received 0 Likes on 0 Posts
Snoop 95 Snoop 95 Snoop 95 Snoop 95 Snoop 95 Snoop 95 Snoop 95 Snoop 95 Snoop 95 Snoop 95 Snoop 95
Default Re: Need quick answer........should be simple, Honda people inside
Originally Posted by hondabigblock
I like using hondabond on the cam ridges
Me, too.
Snoop 95 is offline  
Reply
Old 07-13-2010, 07:15 PM
  #12  
<----BigBake
Thread Starter
 
LXative's Avatar
 
Join Date: Nov 2002
Location: 919
Posts: 4,505
Likes: 0
Received 0 Likes on 0 Posts
LXative LXative LXative LXative LXative LXative LXative LXative LXative LXative LXative
Default Re: Need quick answer........should be simple, Honda people inside
Originally Posted by bluesrt2004
God made Hondabond himself. Nothing else compares.
Never used it......but GM has some sealant I have used for 9+ years, and it is awesome.

Got the VCG, plugs, and wires done in about 20 minutes. Definitely needed some silicon to hold the gasket into the VC......glad I brought it.
LXative is offline  
Reply
Old 07-13-2010, 07:26 PM
  #13  
woot! :D
 
The Guy's Avatar
 
Join Date: Apr 2010
Location: 7 Cities
Posts: 636
Likes: 0
Received 0 Likes on 0 Posts
The Guy is infamous around these partsThe Guy is infamous around these partsThe Guy is infamous around these partsThe Guy is infamous around these partsThe Guy is infamous around these partsThe Guy is infamous around these partsThe Guy is infamous around these partsThe Guy is infamous around these partsThe Guy is infamous around these partsThe Guy is infamous around these partsThe Guy is infamous around these parts
Default Re: Need quick answer........should be simple, Honda people inside
Originally Posted by jhholloway
not to state the obvious but take a screwdriver and rubber hammer to get the VC off. they get stuck often
You never do that. It could screw up the mating surfaces and could prevent it from sealing right. Just pull. It's not that hard.
The Guy is offline  
Reply
Old 07-14-2010, 07:01 PM
  #14  
Registered Member
 
jhholloway's Avatar
 
Join Date: Jun 2009
Location: Richmond VA
Posts: 288
Likes: 0
Received 0 Likes on 0 Posts
jhholloway jhholloway jhholloway jhholloway jhholloway jhholloway jhholloway jhholloway jhholloway jhholloway jhholloway
Default Re: Need quick answer........should be simple, Honda people inside
Originally Posted by The Guy
You never do that. It could screw up the mating surfaces and could prevent it from sealing right. Just pull. It's not that hard.
it's not going to mess it up unless you are being stupid. A light tap with rubber hammer or back of a screw driver is going to mess it up. Yes if you sit there and jam it in there, but I hope the OP is not that dumb.
jhholloway is offline  
Reply
Old 07-15-2010, 04:15 AM
  #15  
woot! :D
 
The Guy's Avatar
 
Join Date: Apr 2010
Location: 7 Cities
Posts: 636
Likes: 0
Received 0 Likes on 0 Posts
The Guy is infamous around these partsThe Guy is infamous around these partsThe Guy is infamous around these partsThe Guy is infamous around these partsThe Guy is infamous around these partsThe Guy is infamous around these partsThe Guy is infamous around these partsThe Guy is infamous around these partsThe Guy is infamous around these partsThe Guy is infamous around these partsThe Guy is infamous around these parts
Default Re: Need quick answer........should be simple, Honda people inside
I see a mistake in your post that makes it look like you are agreeing with me, but i'll let it be.

And why risk it? why not just pull if all you need is a light tap with a hammer?
The Guy is offline  
Reply
Old 07-15-2010, 06:10 AM
  #16  
Registered Member
 
grant90's Avatar
 
Join Date: Sep 2009
Posts: 212
Likes: 0
Received 0 Likes on 0 Posts
grant90 has disabled reputation
Default Re: Need quick answer........should be simple, Honda people inside
Just wondering why did you use silicon to hold the gasket on your VC, I've changed a few VC gaskets and I've NEVER used silicon to hold it together.
grant90 is offline  
Reply
Old 07-15-2010, 09:23 AM
  #17  
Registered member
 
rowe4166's Avatar
 
Join Date: Jan 2003
Posts: 1,213
Likes: 0
Received 0 Likes on 0 Posts
rowe4166 rowe4166 rowe4166 rowe4166 rowe4166 rowe4166 rowe4166 rowe4166 rowe4166 rowe4166 rowe4166
Default Re: Need quick answer........should be simple, Honda people inside
I just use it on the sharp bends around the cam caps
rowe4166 is offline  
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Need a quick answer NOVA people...
BLACK JEFF
NOVA/DC/MD
19
10-28-2005 04:41 AM
Honda people. Need some help
Visualimpact757
Tech Talk
3
06-01-2004 08:27 AM
your car should be banned
Mr.2
Automotive Discussion
36
03-10-2003 07:05 AM
ALL Honda people looking to buy stuff in NOVA......
Dr. On Point
NOVA/DC/MD
7
02-06-2003 04:41 AM
Back to Subforum
Tech Talk
View Next Unread
vtec trouble




Advanced Search
Quick Reply: Need quick answer........should be simple, Honda people inside


Reply Closed Thread Share

All times are GMT -8. The time now is 05:43 AM.