Notices
Tech Talk Anything technically related to your vehicle should be posted here. If you're looking to have work done, try one of the Regional Forums.

97 GSR won't start after new clutch

Thread Tools
 
Old 12-16-2009, 02:19 PM
  #1  
fuck this shit
Thread Starter
 
grgazn's Avatar
 
Join Date: Jul 2008
Location: VA Beach
Posts: 1,840
Likes: 0
Received 0 Likes on 0 Posts
grgazn grgazn grgazn grgazn grgazn grgazn grgazn grgazn grgazn grgazn grgazn
Default 97 GSR won't start after new clutch

I tested everything. I am replacing starter now... It blew smoke when i tried starting it up first time. any suggestions?
Here's a list of what's new:
NGK Iridium spark plugs
NGK Wires
Replacement cap
Replacement rotor
Competition stage 2 clutch
stock, resurfaced flywheel

yes, i aligned everything right
yes the starter wires were all connected when said incident occured
and the grounds to thermostat
and grounds to starter.

Please help ASAP

Thanks
grgazn is offline  
Old 12-16-2009, 02:27 PM
  #2  
fuck this shit
Thread Starter
 
grgazn's Avatar
 
Join Date: Jul 2008
Location: VA Beach
Posts: 1,840
Likes: 0
Received 0 Likes on 0 Posts
grgazn grgazn grgazn grgazn grgazn grgazn grgazn grgazn grgazn grgazn grgazn
Default Re: 97 GSR won't start after new clutch

help asap txt: (757) 597-5166
grgazn is offline  
Old 12-16-2009, 03:22 PM
  #3  
Registered Member
 
jspecteg's Avatar
 
Join Date: Aug 2009
Posts: 59
Likes: 0
Received 0 Likes on 0 Posts
jspecteg is an unknown quantity at this point
Default Re: 97 GSR won't start after new clutch

what do you mean by it wont start does it try to crank or not now did you see how much volts your putting out to the starter, see how many ohms your puting out the wire from the batt to starter, are you getting fuel to the injectors , are you getting spark to the plugs

i dont know how you replaced the clutch and what you did or didnt disconnect i would look and see if you have any plugs not hooked up first

hope this helps
jspecteg is offline  
Old 12-16-2009, 04:40 PM
  #4  
fuck this shit
Thread Starter
 
grgazn's Avatar
 
Join Date: Jul 2008
Location: VA Beach
Posts: 1,840
Likes: 0
Received 0 Likes on 0 Posts
grgazn grgazn grgazn grgazn grgazn grgazn grgazn grgazn grgazn grgazn grgazn
Default Re: 97 GSR won't start after new clutch

yes. i am getting all those things
charge from batt to starter
spark
just replaced fuel filter too.

idk wtf is going on with this stupid thing
grgazn is offline  
Old 12-16-2009, 04:58 PM
  #5  
Registered Member
 
jspecteg's Avatar
 
Join Date: Aug 2009
Posts: 59
Likes: 0
Received 0 Likes on 0 Posts
jspecteg is an unknown quantity at this point
Default Re: 97 GSR won't start after new clutch

well if you cant get it running in a couple of days let me know and ill come take a look and see what your talking about

btw i bought that power lock mod from you
jspecteg is offline  
Old 12-16-2009, 07:50 PM
  #6  
fuck this shit
Thread Starter
 
grgazn's Avatar
 
Join Date: Jul 2008
Location: VA Beach
Posts: 1,840
Likes: 0
Received 0 Likes on 0 Posts
grgazn grgazn grgazn grgazn grgazn grgazn grgazn grgazn grgazn grgazn grgazn
Default Re: 97 GSR won't start after new clutch

Originally Posted by jspecteg
well if you cant get it running in a couple of days let me know and ill come take a look and see what your talking about

btw i bought that power lock mod from you
word. yeah, i think i figured it out... my jackass friend gave me the wrong instructions, i knew they were wrong, but he insisted... here's what he said in short:
put the clutch disk on alignment tool, put the small ring bearing on tool, jam in tranny, and bolt pressure plate housing

later i re-checked everything....
small ring bearing had busted. turned out i was right... it goes in this order, starting from block
Block --> ring bearing --> flywheel --> clutch disk --> pressure plate housing --> throw out bearing --> tranny


i believe that is correct, right?
grgazn is offline  
Old 12-16-2009, 07:53 PM
  #7  
Slammedxpert
 
SortaFlush's Avatar
 
Join Date: Oct 2007
Location: Virginia Beach
Posts: 6,825
Likes: 0
Received 0 Likes on 0 Posts
SortaFlush SortaFlush SortaFlush SortaFlush SortaFlush SortaFlush SortaFlush SortaFlush SortaFlush SortaFlush SortaFlush
Default Re: 97 GSR won't start after new clutch

Damn, you threw a bunch of un-necessary parts at it.

Lol.

What is this "ring bearing" your talking about?

The one that goes in the flywheel....pilot bearing.....?
SortaFlush is offline  
Old 12-17-2009, 01:56 PM
  #8  
fuck this shit
Thread Starter
 
grgazn's Avatar
 
Join Date: Jul 2008
Location: VA Beach
Posts: 1,840
Likes: 0
Received 0 Likes on 0 Posts
grgazn grgazn grgazn grgazn grgazn grgazn grgazn grgazn grgazn grgazn grgazn
Default Re: 97 GSR won't start after new clutch

figured it out. finally done with this shit
grgazn is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
93dateggy
Tech Talk
7
09-09-2009 04:24 PM
bsershatch
Tech Talk
7
12-01-2008 06:09 PM
bsershatch
Tech Talk
6
10-24-2008 09:03 PM
-Danimal
Tech Talk
20
10-06-2003 05:01 PM
see are x
Tech Talk
35
03-20-2003 11:21 AM



Quick Reply: 97 GSR won't start after new clutch



All times are GMT -8. The time now is 08:34 PM.