450 DSM injector question an timming
07-23-2006, 11:59 PM
#1
Im in CA Now!!
Thread Starter
Join Date: May 2006
Posts: 524
Likes: 0
Received 0 Likes
on
0 Posts
450 DSM injector question an timming
Crome says them injectors are max out on 10psi on my car. is that right. i dont think so. Im only running 7psi so im not trying to stress the injectors out.
also im running 20 degrees timming at WOT on &psi. That should be pretty safe corrrect?
also im running 20 degrees timming at WOT on &psi. That should be pretty safe corrrect?
07-24-2006, 12:41 AM
#2
Registered Member
Join Date: Apr 2003
Location: Richmond VA
Posts: 2,569
Likes: 0
Received 0 Likes
on
0 Posts
Re: 450 DSM injector question an timming
at 10psi you should be around 300whp or more so yes those injectors will be pushing it. Try cranking up your fuel pressure if you want to run 10psi.
07-24-2006, 05:37 AM
#3
Im in CA Now!!
Thread Starter
Join Date: May 2006
Posts: 524
Likes: 0
Received 0 Likes
on
0 Posts
Re: 450 DSM injector question an timming
Originally Posted by sohc_mshue
at 10psi you should be around 300whp or more so yes those injectors will be pushing it. Try cranking up your fuel pressure if you want to run 10psi.
how the timming?
07-24-2006, 09:07 AM
#5
Registered Member
Join Date: Apr 2003
Location: Richmond VA
Posts: 2,569
Likes: 0
Received 0 Likes
on
0 Posts
Re: 450 DSM injector question an timming
the timing doesn't sound bad for a base. I usually use 1deg/psi retard for a basemap. Make sure you pull plugs or use a knock detection device to check for knock.
07-24-2006, 10:15 AM
#6
Im in CA Now!!
Thread Starter
Join Date: May 2006
Posts: 524
Likes: 0
Received 0 Likes
on
0 Posts
Re: 450 DSM injector question an timming
Originally Posted by sohc_mshue
the timing doesn't sound bad for a base. I usually use 1deg/psi retard for a basemap. Make sure you pull plugs or use a knock detection device to check for knock.
07-24-2006, 12:41 PM
#7
Registered member
Join Date: May 2003
Posts: 6,141
Likes: 0
Received 0 Likes
on
0 Posts
Re: 450 DSM injector question an timming
Hey,
CROME's calculation is incorrect once you scale injectors I believe..
so its not correct.
20 deg total timing seems perfectly fine for 7 psi
CROME's calculation is incorrect once you scale injectors I believe..
so its not correct.
20 deg total timing seems perfectly fine for 7 psi
07-24-2006, 12:54 PM
#8
Im in CA Now!!
Thread Starter
Join Date: May 2006
Posts: 524
Likes: 0
Received 0 Likes
on
0 Posts
Re: 450 DSM injector question an timming
Originally Posted by GaRn
Hey,
CROME's calculation is incorrect once you scale injectors I believe..
so its not correct.
20 deg total timing seems perfectly fine for 7 psi
CROME's calculation is incorrect once you scale injectors I believe..
so its not correct.
20 deg total timing seems perfectly fine for 7 psi
07-25-2006, 07:33 AM
#9
Registered Member
Join Date: Apr 2003
Location: Richmond VA
Posts: 2,569
Likes: 0
Received 0 Likes
on
0 Posts
Re: 450 DSM injector question an timming
Originally Posted by TheBigShot
i checked plugs...they look good. i have a p28 so i dont have knock.
. I meant use a knock detection device to listen.
07-25-2006, 07:39 AM
#10
Im in CA Now!!
Thread Starter
Join Date: May 2006
Posts: 524
Likes: 0
Received 0 Likes
on
0 Posts
Re: 450 DSM injector question an timming
Originally Posted by sohc_mshue
you can still have knock without having a knock sensor . I meant use a knock detection device to listen.
. I meant use a knock detection device to listen.
Thread
Thread Starter
Forum
Replies
Last Post