idle problems
#1
Hi
Thread Starter
Join Date: Aug 2008
Location: Va Beach_757
Posts: 2,261
Likes: 0
Received 0 Likes
on
0 Posts
idle problems
Car. 93 integra with swapped b20b
Problem. car idles at 3k warm or cold. car also bogs down when driving.
Mods. I/H/E, exedy clutch, 7.5lb flywheel
I just finished my b20 swap into my DA. Car is not throwing any CELs. It will idle at 3k. I unplugged the map sensor and it dropped to 2,200. Plugged it back in and it rose again. I unplugged the IACV and it dropped to just below 2k, plugged it back up and it rose again. Ive tried adjusting the idle screw but it doesnt do anything. I dont know what to do next? Thanks for any advice. Also, anybody in the Hampton/Newport News area is welcome to come take a look at it.
EDIT: Everything is OBD1
Problem. car idles at 3k warm or cold. car also bogs down when driving.
Mods. I/H/E, exedy clutch, 7.5lb flywheel
I just finished my b20 swap into my DA. Car is not throwing any CELs. It will idle at 3k. I unplugged the map sensor and it dropped to 2,200. Plugged it back in and it rose again. I unplugged the IACV and it dropped to just below 2k, plugged it back up and it rose again. Ive tried adjusting the idle screw but it doesnt do anything. I dont know what to do next? Thanks for any advice. Also, anybody in the Hampton/Newport News area is welcome to come take a look at it.
EDIT: Everything is OBD1
Last edited by Integra2Be; 11-02-2010 at 08:05 AM.
#4
Re: idle problems
Maybe there is a leak somewhere in the intake manifold. make sure everything is tight and that all vacuum lines are in place and secure. even a small hole in one of the vacuum lines can cause problems.
Have you checked the IACV?
Have you checked the IACV?
#5
Hi
Thread Starter
Join Date: Aug 2008
Location: Va Beach_757
Posts: 2,261
Likes: 0
Received 0 Likes
on
0 Posts
Re: idle problems
Maybe there is a leak somewhere in the intake manifold. make sure everything is tight and that all vacuum lines are in place and secure. even a small hole in one of the vacuum lines can cause problems. get soap and water in a spray bottle and spray all your vac lines to try and find the leak (if there is one)... the water will bubble up at the leaking spot.
however, i did delete the charcoal canister and now there is an open port on the TB.
#9
RIP DRAGVA-2016
Join Date: Sep 2008
Location: super secret
Posts: 17,242
Likes: 0
Received 0 Likes
on
0 Posts
Re: idle problems
Car. 93 integra with swapped b20b
Problem. car idles at 3k warm or cold. car also bogs down when driving.
Mods. I/H/E, exedy clutch, 7.5lb flywheel
I just finished my b20 swap into my DA. Car is not throwing any CELs. It will idle at 3k. I unplugged the map sensor and it dropped to 2,200. Plugged it back in and it rose again. I unplugged the IACV and it dropped to just below 2k, plugged it back up and it rose again. Ive tried adjusting the idle screw but it doesnt do anything. I dont know what to do next? Thanks for any advice. Also, anybody in the Hampton/Newport News area is welcome to come take a look at it.
EDIT: Everything is OBD1
Problem. car idles at 3k warm or cold. car also bogs down when driving.
Mods. I/H/E, exedy clutch, 7.5lb flywheel
I just finished my b20 swap into my DA. Car is not throwing any CELs. It will idle at 3k. I unplugged the map sensor and it dropped to 2,200. Plugged it back in and it rose again. I unplugged the IACV and it dropped to just below 2k, plugged it back up and it rose again. Ive tried adjusting the idle screw but it doesnt do anything. I dont know what to do next? Thanks for any advice. Also, anybody in the Hampton/Newport News area is welcome to come take a look at it.
EDIT: Everything is OBD1