eg intake manifold hook up
#1
Banned
Thread Starter
Join Date: Sep 2006
Location: Va beach
Posts: 830
Likes: 0
Received 0 Likes
on
0 Posts
eg intake manifold hook up
does anyone know the schematics to hooking a z6 intake manifold up,ive tryed searching but i can not find anything and i have limited axcess to the internet now
if anyone has a z6 in a eg and would like to make a few bucks by driving out near the best buy on independence so i can cross reference then hit me
7572375927
if anyone has a z6 in a eg and would like to make a few bucks by driving out near the best buy on independence so i can cross reference then hit me
7572375927
#2
TurboPipingSystems
Join Date: Jul 2003
Location: USDM Land, Va Bch
Posts: 1,483
Likes: 0
Received 0 Likes
on
0 Posts
Re: eg intake manifold hook up
I dont understand exactly what you are trying to do..... it should be the same as whatever you have on there now.... Z6 is an OBD1 manifold.... and so as an EG....
#3
Banned
Thread Starter
Join Date: Sep 2006
Location: Va beach
Posts: 830
Likes: 0
Received 0 Likes
on
0 Posts
Re: eg intake manifold hook up
i know,i have never messed with a obd1 car before so im not sure which wires go to which sensors,like i have a extra one just hanging around,and im not sure where all the lines go,i have a extra line also.
point is i know i dont have something hooked up correctly because the car surges after i jsut put on a brand new intake manifold gasket and torqued it down to specs from the haynes manual
point is i know i dont have something hooked up correctly because the car surges after i jsut put on a brand new intake manifold gasket and torqued it down to specs from the haynes manual
#4
TurboPipingSystems
Join Date: Jul 2003
Location: USDM Land, Va Bch
Posts: 1,483
Likes: 0
Received 0 Likes
on
0 Posts
Re: eg intake manifold hook up
From the harness, back side of the intake manifold, i can only think of two connectors that are indentical: IACV and IAT. Maybe you have these crossed. Have you mechanically adjusted the TB to see if there is any improvements on the surging?
Last edited by thermal; 01-20-2007 at 08:16 AM. Reason: correction
#5
Banned
Thread Starter
Join Date: Sep 2006
Location: Va beach
Posts: 830
Likes: 0
Received 0 Likes
on
0 Posts
Re: eg intake manifold hook up
i have tryed to cross many of the plugs and yes i have tryed adjusting the idle,it did this same thing with a crx si intake manifold and a hf manifold
could there be something wrong with the motor its self to cause the surging,i bought a haynes manual but its not very usefull in my opinion
could there be something wrong with the motor its self to cause the surging,i bought a haynes manual but its not very usefull in my opinion
#6
TurboPipingSystems
Join Date: Jul 2003
Location: USDM Land, Va Bch
Posts: 1,483
Likes: 0
Received 0 Likes
on
0 Posts
Re: eg intake manifold hook up
Have you done a compression test? DL Helms manual for free at www.hondahookup.com
#7
Banned
Thread Starter
Join Date: Sep 2006
Location: Va beach
Posts: 830
Likes: 0
Received 0 Likes
on
0 Posts
Re: eg intake manifold hook up
naw i havent done a compression test i have a jdmd15b swap ready to go in but i want to wait to see if i can get reliability out of the b8 with a6 head
Thread
Thread Starter
Forum
Replies
Last Post
jujub1
Want to Buy / Trade ARCHIVE
12
01-25-2008 04:21 AM