b series wont rev past 4000
#1
Registered Member
Thread Starter
Join Date: Dec 2006
Location: sleeping in my car
Posts: 616
Likes: 0
Received 0 Likes
on
0 Posts
b series wont rev past 4000
im working with a swapped eg.....its a obd2 motor, along with the ecu for said motor. wont rev past 4000. has a slightly high idle. could be anything i guess, it was just thrown together. yall will probably be able to figure it out imidiatley, i just know nothing about this car. it had a motor go bad in it, and had another one put in, and abandoned halfway through. car runs good down the road. just wont go past 4000. it ran great before. im asuming somethings not hooked up right, i just need to know what.
#2
Re: b series wont rev past 4000
tune ? if you havent tried tuning it that might be your problem the ecu could have ben tuned for another car, different set up. even different motor
#3
Registered Member
Join Date: Jul 2005
Location: Richmond
Posts: 241
Likes: 0
Received 0 Likes
on
0 Posts
Re: b series wont rev past 4000
its a obd2 motor, along with the ecu for said motor
#4
Registered Member
Thread Starter
Join Date: Dec 2006
Location: sleeping in my car
Posts: 616
Likes: 0
Received 0 Likes
on
0 Posts
Re: b series wont rev past 4000
yeah. all this is is a swap that ran, and had the engine replaced with an identicall one. ive got a check engine light, when im done pulling this buick 3800 motor, ill get back to you guys with the code.
#5
Registered Member
Join Date: Apr 2008
Location: Harrisonburg
Posts: 320
Likes: 0
Received 0 Likes
on
0 Posts
Re: b series wont rev past 4000
sounds like it could be the distributor i.e. coil, ignitor etc. or possibly the ECU could be in limp mode although it's not very common. what motor and ecu are you running?
Last edited by TypeSTurbo; 08-04-2009 at 04:15 PM.
#6
Registered Member
Thread Starter
Join Date: Dec 2006
Location: sleeping in my car
Posts: 616
Likes: 0
Received 0 Likes
on
0 Posts
Re: b series wont rev past 4000
a b18 and matched ecu. obd2. i thought it was a limp mode thing too.....but 5000 rpm, is that limp mode? (itll rev to that, then fuel cut/rev limiter/whatever) i just really need the writeup for a obd2 swap......like, sensors used, and vacume routing......i dont know whats used and not used. AGAIN this thing ran fine, blew the motor up, and this is a suplicate of the old motor. obd2 b18, thats all i can tell you. EVERYTHING was switched over. i dunno. im used to nissans. know nothing about hondas.
#8
JDM Monkey Tuning
Join Date: Feb 2006
Location: va beach
Posts: 639
Likes: 0
Received 0 Likes
on
0 Posts
#10
Registered Member
Thread Starter
Join Date: Dec 2006
Location: sleeping in my car
Posts: 616
Likes: 0
Received 0 Likes
on
0 Posts
Re: b series wont rev past 4000
i was wondering about the distributor.....i guess they COULD have put it in 180 degrees wrong. ill take a quick look. it was aa previous b18 in the car. the b18 started smoking. the motor in it NOW replaced the one that was smoking. it was put back together, and im only asumming they got all the sensors right. i guess i need to use a scanner, the whole cars been converted to obd2. i DO have a check engine light.