VADriven.com Forums

Notices
Tech Talk Anything technically related to your vehicle should be posted here. If you're looking to have work done, try one of the Regional Forums.

about b16

Thread Tools
 
Old 06-29-2003, 10:01 AM
  #1  
Registered User
Thread Starter
 
stockcrx's Avatar
 
Join Date: Nov 2002
Location: yorktown
Posts: 80
Likes: 0
Received 0 Likes on 0 Posts
stockcrx is an unknown quantity at this point
Question about b16 swap
i ran into a few probs while doing my swap. im swaping a b16 ito a 91 hf .i got the wiring sub harness from hasport and it was supposed to be"plug and play". everything plugged up except the injector control module because the plug off the hasport has 4 extra wires compared to the stock b16 plug so i was wanderin waht i would with that? and then i got a Y1 tranny and the axles dont fit so i read up that i have to to get 86-89 integra axles and use 90-93 cv joints so i was jstu wanderin if that was right. any help would be greatly appiciated.
Last edited by stockcrx; 06-29-2003 at 10:10 AM.
stockcrx is offline  
Reply
Old 06-29-2003, 10:49 AM
  #2  
Registered User
Thread Starter
 
stockcrx's Avatar
 
Join Date: Nov 2002
Location: yorktown
Posts: 80
Likes: 0
Received 0 Likes on 0 Posts
stockcrx is an unknown quantity at this point
Default
tops
stockcrx is offline  
Reply
Old 06-29-2003, 11:48 AM
  #3  
Registered User
Thread Starter
 
stockcrx's Avatar
 
Join Date: Nov 2002
Location: yorktown
Posts: 80
Likes: 0
Received 0 Likes on 0 Posts
stockcrx is an unknown quantity at this point
Default
stockcrx is offline  
Reply
Old 06-29-2003, 06:26 PM
  #4  
Registered User
Thread Starter
 
stockcrx's Avatar
 
Join Date: Nov 2002
Location: yorktown
Posts: 80
Likes: 0
Received 0 Likes on 0 Posts
stockcrx is an unknown quantity at this point
Default
ttt
stockcrx is offline  
Reply
Old 06-30-2003, 01:57 PM
  #5  
Registered User
Thread Starter
 
stockcrx's Avatar
 
Join Date: Nov 2002
Location: yorktown
Posts: 80
Likes: 0
Received 0 Likes on 0 Posts
stockcrx is an unknown quantity at this point
Default
damn no o ne can help a brother out?
stockcrx is offline  
Reply
Old 06-30-2003, 03:45 PM
  #6  
Awesome.
 
MA-HALF-E's Avatar
 
Join Date: Nov 2002
Location: Virginia Beach
Posts: 13,483
Likes: 0
Received 0 Likes on 0 Posts
MA-HALF-E MA-HALF-E MA-HALF-E MA-HALF-E MA-HALF-E MA-HALF-E MA-HALF-E MA-HALF-E MA-HALF-E MA-HALF-E MA-HALF-E
Default
You need the correct hubs when swapping a B-series into an HF. Not sure on which hubs though...
MA-HALF-E is offline  
Reply
Old 07-01-2003, 09:20 AM
  #7  
Registered User
 
dohcEG's Avatar
 
Join Date: Nov 2002
Location: va beach
Posts: 37
Likes: 0
Received 0 Likes on 0 Posts
dohcEG is an unknown quantity at this point
Default
you need 5 speed hubs if they are not already
dohcEG is offline  
Reply
Old 07-01-2003, 06:55 PM
  #8  
hybrid no more :(
 
Bert's Avatar
 
Join Date: Apr 2003
Location: Virginia Beach
Posts: 241
Likes: 0
Received 0 Likes on 0 Posts
Bert Bert Bert Bert Bert Bert Bert Bert Bert Bert Bert
Default
doesn't have to be 5 speed....automatic ones will work...just cannot be 4 speed or hf's....got automatic ones w/ my lsvtec...
bert
Bert is offline  
Reply
Old 07-03-2003, 10:11 AM
  #9  
homewreker
 
LS_crx's Avatar
 
Join Date: Nov 2002
Posts: 338
Likes: 0
Received 0 Likes on 0 Posts
LS_crx LS_crx LS_crx LS_crx LS_crx LS_crx LS_crx LS_crx LS_crx LS_crx LS_crx
Default
yo wes give a call
LS_crx is offline  
Reply
Old 07-03-2003, 10:21 AM
  #10  
EEK
卐 Walnuts
 
EEK's Avatar
 
Join Date: Nov 2002
Location: Compton, Ca W
Posts: 29,360
Likes: 0
Received 0 Likes on 0 Posts
EEK EEK EEK EEK EEK EEK EEK EEK EEK EEK EEK
Default
my boy is using a ys1 i think whatever the xsi tranny is, 89 integ axles..and the front hubs/rotors etc off a xsi
EEK is offline  
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Eagle B16 Rods | B16 ACL Bearings (New) | 81.5mm 9:1 or 10:1 Pistons (New)
Broke B16
Engine / Exhaust / Drivetrain
0
03-23-2009 03:06 PM
WTB: NoVa: Bare B20 Block and B16 Head and B16 transmission
imcnblu
Want to Buy / Trade ARCHIVE
2
06-11-2008 05:24 PM
Stock B16 cams,B16 intake manifold,fuelpump and ecu!!
kenbdSi
Parts ARCHIVE
9
06-04-2008 02:27 PM
Back to Subforum
Tech Talk
View Next Unread
quick firing order question




Advanced Search
Quick Reply: about b16


Reply Closed Thread Share

All times are GMT -8. The time now is 12:06 AM.