Tons of foxbody parts
#1
Simple Bolt Ons
Thread Starter
Join Date: Nov 2002
Location: Hampton
Posts: 438
Likes: 0
Received 0 Likes
on
0 Posts
Tons of foxbody parts
Billy Weston
Hampton
757-329-4868
There are still a lot more parts that haven't been listed yet nor have I decided what I'll sell it for so please bare with me if the response is a little slow. I would like to keep the shortblock together if possible.
ENGINE PARTS:
Stock, filled 351 block bored to 357 c.i.
Wiseco Pro tru flat top forged pistons
Forged I beam rods
Stock 69 351 crank
Manley Pushrods
Comp Valve springs and Rockers
Comp Retro Fit lifters
Comp XR294RF-HR Cam
Edelbrock Victor Jr 70 CC heads
FMS red on black valve covers
Milodan 7 Qt Pan
Edelbrock Victor Jr intake
750 Mighty Demon carb $3500 carb to pan will split up top end of motor
Trick Flow TFS-R upper intake $250
Griffin Aluminum Radiator with flex-a-lite 15" electric fan $200
pro-m maf and 30 lbs injectors $200
bbk cai $20
Edelbrock 75mm TB $125
Aeromotive Fuel Regulator for carb
Autogauge Fuel Press. Gauge
MSD Pro Billet Distributor for carbed 351W $175
Exhaust - Custom Kooks headers
Kooks 3" X-pipe
Flowmaster 3" 2 Chamber Mufflers to dumps $500
Transmission -
Tremec 3550
Pro 5.0 shifter
Lakewood blowproof bell
fms billet steel flywheel 28oz
Anderson High Rev clutch $1200
Rear End - Moser 31 Spline Axles
Moser C-clip Eliminators
Detroit Locker
FRPP 4.10 Gears
FRPP Rear End Girdle
Moroso long wheel studs
(I'm not sure on the sale for this.... I may swap some of the guts to a new rearend for the cobra) $900
Suspension -
QA1 Pro-Kit K-member, control arms, coilovers and shocks, Caster-Camber plates $700
Lakewood lower control arms
Taylor Alum Box $75
Autometer Phantom Oil, Water, and Nitrous gauges
2 RCI 5 Pt harnesses
15X8 Weld Draglights with 275/50 MT Et Street Radials
Weld Draglight skinnies in the front $500
Hampton
757-329-4868
There are still a lot more parts that haven't been listed yet nor have I decided what I'll sell it for so please bare with me if the response is a little slow. I would like to keep the shortblock together if possible.
ENGINE PARTS:
Stock, filled 351 block bored to 357 c.i.
Wiseco Pro tru flat top forged pistons
Forged I beam rods
Stock 69 351 crank
Manley Pushrods
Comp Valve springs and Rockers
Comp Retro Fit lifters
Comp XR294RF-HR Cam
Edelbrock Victor Jr 70 CC heads
FMS red on black valve covers
Milodan 7 Qt Pan
Edelbrock Victor Jr intake
750 Mighty Demon carb $3500 carb to pan will split up top end of motor
Trick Flow TFS-R upper intake $250
Griffin Aluminum Radiator with flex-a-lite 15" electric fan $200
pro-m maf and 30 lbs injectors $200
bbk cai $20
Edelbrock 75mm TB $125
Aeromotive Fuel Regulator for carb
Autogauge Fuel Press. Gauge
MSD Pro Billet Distributor for carbed 351W $175
Exhaust - Custom Kooks headers
Kooks 3" X-pipe
Flowmaster 3" 2 Chamber Mufflers to dumps $500
Transmission -
Tremec 3550
Pro 5.0 shifter
Lakewood blowproof bell
fms billet steel flywheel 28oz
Anderson High Rev clutch $1200
Rear End - Moser 31 Spline Axles
Moser C-clip Eliminators
Detroit Locker
FRPP 4.10 Gears
FRPP Rear End Girdle
Moroso long wheel studs
(I'm not sure on the sale for this.... I may swap some of the guts to a new rearend for the cobra) $900
Suspension -
QA1 Pro-Kit K-member, control arms, coilovers and shocks, Caster-Camber plates $700
Lakewood lower control arms
Taylor Alum Box $75
Autometer Phantom Oil, Water, and Nitrous gauges
2 RCI 5 Pt harnesses
15X8 Weld Draglights with 275/50 MT Et Street Radials
Weld Draglight skinnies in the front $500
Thread
Thread Starter
Forum
Replies
Last Post