FS: all motor ls/vtec 210whp smsp skunk2 tons of parts needs to go 5000miles on all!!
#1
VTEC
Thread Starter
Join Date: Nov 2004
Location: Newport news 757
Posts: 1,543
Likes: 0
Received 0 Likes
on
0 Posts
FS: all motor ls/vtec 210whp smsp skunk2 tons of parts needs to go 5000miles on all!!
i am sellin my fully built all motor setup cause i need the money asap to buy another motor for another route im goin. it was tuned and put 210 down by inline pro does not come with ecu unless you pay the extrafor my (s300)
runs on 93 octane
motor is at about 12:8:1 compression
everything has 5200 miles on it
motor is in the car can show how well it runs pulls stong as a bitch
95 gsr head port and polished
full skunk2 valve train
skunk2 pro 1 cams and cam gears
3 angle valve job
shaved 10 thousandths
skunk2 pro series intake manifold with 70 mm skunk2 port matched throttle body
hondata im gasket
rc 440cc injectors obd1
new dizzy
b18b block
aebs head studs
cp 12:5:1 pistons 81mm
eagle h beam rods
micro polished crank
acl race bearing
new 99gsr oil pump
new gsr water pump
SMSP header!!!
trans your choice--
have both a cable and hydro tranny i can work with have a competiton clutch for both stage 4 they both have about 2500 miles on each both min condition
have axles for the cable set up
any questions please ask
asking 3500 i have over 6000 invested
757 329 0472
runs on 93 octane
motor is at about 12:8:1 compression
everything has 5200 miles on it
motor is in the car can show how well it runs pulls stong as a bitch
95 gsr head port and polished
full skunk2 valve train
skunk2 pro 1 cams and cam gears
3 angle valve job
shaved 10 thousandths
skunk2 pro series intake manifold with 70 mm skunk2 port matched throttle body
hondata im gasket
rc 440cc injectors obd1
new dizzy
b18b block
aebs head studs
cp 12:5:1 pistons 81mm
eagle h beam rods
micro polished crank
acl race bearing
new 99gsr oil pump
new gsr water pump
SMSP header!!!
trans your choice--
have both a cable and hydro tranny i can work with have a competiton clutch for both stage 4 they both have about 2500 miles on each both min condition
have axles for the cable set up
any questions please ask
asking 3500 i have over 6000 invested
757 329 0472
Last edited by diggity dave; 04-16-2008 at 08:29 PM.
#2
VTEC
Thread Starter
Join Date: Nov 2004
Location: Newport news 757
Posts: 1,543
Likes: 0
Received 0 Likes
on
0 Posts
Re: FS: all motor ls/vtec 210whp smsp skunk2 tons of parts needs to go 5000miles on a
ttt
#3
Ohhh Snap
Join Date: Oct 2007
Location: Virginia beach
Posts: 4,535
Likes: 0
Received 0 Likes
on
0 Posts
Re: FS: all motor ls/vtec 210whp smsp skunk2 tons of parts needs to go 5000miles on a
ahh so this is the motor you were talking about.Gl it sounds nasty
#4
VTEC
Thread Starter
Join Date: Nov 2004
Location: Newport news 757
Posts: 1,543
Likes: 0
Received 0 Likes
on
0 Posts
Re: FS: all motor ls/vtec 210whp smsp skunk2 tons of parts needs to go 5000miles on a
Yep this is the one
#5
Re: FS: all motor ls/vtec 210whp smsp skunk2 tons of parts needs to go 5000miles on a
trade for a stock b16 and 39 dollars?
#6
VTEC
Thread Starter
Join Date: Nov 2004
Location: Newport news 757
Posts: 1,543
Likes: 0
Received 0 Likes
on
0 Posts
Re: FS: all motor ls/vtec 210whp smsp skunk2 tons of parts needs to go 5000miles on a
tempting but Im leaning towards no
#7
VTEC
Thread Starter
Join Date: Nov 2004
Location: Newport news 757
Posts: 1,543
Likes: 0
Received 0 Likes
on
0 Posts
Re: FS: all motor ls/vtec 210whp smsp skunk2 tons of parts needs to go 5000miles on a
ttt
#8
VTEC
Thread Starter
Join Date: Nov 2004
Location: Newport news 757
Posts: 1,543
Likes: 0
Received 0 Likes
on
0 Posts
Re: FS: all motor ls/vtec 210whp smsp skunk2 tons of parts needs to go 5000miles on a
up
#9
Re: FS: all motor ls/vtec 210whp smsp skunk2 tons of parts needs to go 5000miles on a
i beat this in my single cam. bump for a clean swap.
#10
Re: FS: all motor ls/vtec 210whp smsp skunk2 tons of parts needs to go 5000miles on a
good luck with the sale dude