fs: JL 1200watt monoblock amp *like new* cheap
Thread Starter
HighestTraderRating
Joined: Jun 2005
Posts: 4,389
Likes: 0
Re: fs: JL 1200watt monoblock amp *like new* cheap
Blactical Actual.
Joined: Oct 2004
Posts: 2,551
Likes: 0
From: Norfolk/ Va Beach
Re: fs: JL 1200watt monoblock amp *like new* cheap
fyi, jl audio's nomenclature on their a/e/g line is the first number designates the channel(s), rest are the power rating. so if this is an e1200 it is (1)channel(200)watts. the slash series are different where the power rating is the first group of numbers and the number after the slash is the number of channels. 300/4 is 300w/4channels.
Manufacturer's Description
JL Audio full-range amplifiers benefit from an exciting new technology: Absolute Symmetry™. This patented Class AB output stage delivers amazing fidelity with extremely low distortion over a wide range of load impedances.
Until now, the accepted approach for building high-fidelity Class AB amplifiers has been to utilize "Complementary" output stages, which use different types of transistors to "push" the speaker and "pull' the speaker. The problem with this approach is that true "mirror-image" transistors are impossible to create, leading to asymmetrical clipping behavior.
Another approach is to use the same type of transistor for both push and pull but without buffering from the load impedance. This solves the problem of asymmetrical clipping, but leads to huge increases in distortion as load impedance drops (making this design less desirable than the "complementary" approach.)
JL Audio amplifiers solve the entire issue once and for all with a revolutionary Class AB circuit that employs identical type transistors for push and pull with true buffering from the load impedance. Our design achieves absolute power symmetry and extremely low distortion over a wide range of load impedances. It is the most significant breakthrough in Class AB circuit design in quite some time and it is patented by JL Audio.
Model e1200
Key Features
Absolute Symmetry™ Class AB Circuit
(U.S. Patent #6,294,959)
Differential, Noise-Cancelling Input Topology:
RCA jack inputs (low-level) and multi-pin jack (high-level)
On-board Crossover:
State-variable, 12dB/octave Butterworth with continuously variable cutoff frequency selection from 50 – 200 Hz. Configurable as Low-Pass or High-Pass
Preamp Output:
Pass-through type.
Speaker output connections:
Accept up to 8 AWG wire
+12V and Ground connections:
Accept up to 4 AWG wire
Specifications
Rated Power (mono):
120 W RMS x 1 @ 4 ohm (12.5V);
200 W RMS x 1 @ 2 ohm (12.5V)
THD at Rated Power:
<0.08% @ 4 ohm (20 Hz -20 kHz)
S/N Ratio:
>104 dB referred to rated power (A-weighted, 20 Hz – 20 kHz noise bandwidth)
Frequency Response:
10 Hz – 25 kHz (+0, -1dB)
Damping Factor:
>200 @ 4 ohm / 50 Hz,
>100 @ 2 ohm / 50 Hz
Slew Rate:
± 22V/µs
Input Range:
200mV – 8V RMS
Dimensions:
9.8" x 9.25" x 2.36"
Manufacturer's Description
JL Audio full-range amplifiers benefit from an exciting new technology: Absolute Symmetry™. This patented Class AB output stage delivers amazing fidelity with extremely low distortion over a wide range of load impedances.
Until now, the accepted approach for building high-fidelity Class AB amplifiers has been to utilize "Complementary" output stages, which use different types of transistors to "push" the speaker and "pull' the speaker. The problem with this approach is that true "mirror-image" transistors are impossible to create, leading to asymmetrical clipping behavior.
Another approach is to use the same type of transistor for both push and pull but without buffering from the load impedance. This solves the problem of asymmetrical clipping, but leads to huge increases in distortion as load impedance drops (making this design less desirable than the "complementary" approach.)
JL Audio amplifiers solve the entire issue once and for all with a revolutionary Class AB circuit that employs identical type transistors for push and pull with true buffering from the load impedance. Our design achieves absolute power symmetry and extremely low distortion over a wide range of load impedances. It is the most significant breakthrough in Class AB circuit design in quite some time and it is patented by JL Audio.
Model e1200
Key Features
Absolute Symmetry™ Class AB Circuit
(U.S. Patent #6,294,959)
Differential, Noise-Cancelling Input Topology:
RCA jack inputs (low-level) and multi-pin jack (high-level)
On-board Crossover:
State-variable, 12dB/octave Butterworth with continuously variable cutoff frequency selection from 50 – 200 Hz. Configurable as Low-Pass or High-Pass
Preamp Output:
Pass-through type.
Speaker output connections:
Accept up to 8 AWG wire
+12V and Ground connections:
Accept up to 4 AWG wire
Specifications
Rated Power (mono):
120 W RMS x 1 @ 4 ohm (12.5V);
200 W RMS x 1 @ 2 ohm (12.5V)
THD at Rated Power:
<0.08% @ 4 ohm (20 Hz -20 kHz)
S/N Ratio:
>104 dB referred to rated power (A-weighted, 20 Hz – 20 kHz noise bandwidth)
Frequency Response:
10 Hz – 25 kHz (+0, -1dB)
Damping Factor:
>200 @ 4 ohm / 50 Hz,
>100 @ 2 ohm / 50 Hz
Slew Rate:
± 22V/µs
Input Range:
200mV – 8V RMS
Dimensions:
9.8" x 9.25" x 2.36"
Thread
Thread Starter
Forum
Replies
Last Post