1990 Mazda Miata
#1
Registered member
Thread Starter
Join Date: Aug 2007
Location: Richmond/Yorktown
Posts: 500
Likes: 0
Received 0 Likes
on
0 Posts
1990 Mazda Miata
Name: Kent
Location: Richmond and Yorktown, VA
Means of contact: Phone(757-812-5917), PM, and this thread.
Price: 3800, negotiable.
Trades: Clean E30, trim model doesn't matter too much. Not too interested in anything else.
1990 mazda miata with a 1996 miata motor
64k on motor 194k on body
Maintenance done around 50k miles (motor miles)
-Swap, 1.8l from 1996
-GC coils
-Koni yellows
-Timing belt
-Timing belt tensioner
-Waterpump
-Clutch
-Flywheel
-Pressure Plate
-Master Cylinder
-Slave Cylinder
-Passenger rear caliper
-New pads, caliper clips, and caliper springs all the way around
-Alternator
-Brake fluid flushed
-Caliper slides and pins replaced and all calipers greased
-Tranny and diff fluid changed
-New Plugs and wires
-Rolled fenders
Other info:
Oil changed every 3k miles. 0w40 mobile 1 synthetic, purolator pure one Mellinia v6 filter
Corrected timing job from previous owner and set to +14 degrees timing (stock is +10)
Inspected
Top doesn't really leak, small holes from where it rubs top frame
Replaced broken interior panels, including drivers side arm rest. All panels are there and intact.
New tires 205/50/R15, right around 1,000 miles on them.
New radiator and cap, right around 1,000 miles on them.
100% problem FREE Installed gaskets and new thermoswitch,
I'll try and snap some more pictures tomorrow after work.
First picture is the most current one.
More pics further down page.
Location: Richmond and Yorktown, VA
Means of contact: Phone(757-812-5917), PM, and this thread.
Price: 3800, negotiable.
Trades: Clean E30, trim model doesn't matter too much. Not too interested in anything else.
1990 mazda miata with a 1996 miata motor
64k on motor 194k on body
Maintenance done around 50k miles (motor miles)
-Swap, 1.8l from 1996
-GC coils
-Koni yellows
-Timing belt
-Timing belt tensioner
-Waterpump
-Clutch
-Flywheel
-Pressure Plate
-Master Cylinder
-Slave Cylinder
-Passenger rear caliper
-New pads, caliper clips, and caliper springs all the way around
-Alternator
-Brake fluid flushed
-Caliper slides and pins replaced and all calipers greased
-Tranny and diff fluid changed
-New Plugs and wires
-Rolled fenders
Other info:
Oil changed every 3k miles. 0w40 mobile 1 synthetic, purolator pure one Mellinia v6 filter
Corrected timing job from previous owner and set to +14 degrees timing (stock is +10)
Inspected
Top doesn't really leak, small holes from where it rubs top frame
Replaced broken interior panels, including drivers side arm rest. All panels are there and intact.
New tires 205/50/R15, right around 1,000 miles on them.
New radiator and cap, right around 1,000 miles on them.
100% problem FREE Installed gaskets and new thermoswitch,
I'll try and snap some more pictures tomorrow after work.
First picture is the most current one.
More pics further down page.
Last edited by KingNOthingFTW; 07-20-2010 at 09:28 AM.
#2
Officially Official
Join Date: Aug 2007
Location: Klofron
Posts: 1,980
Likes: 0
Received 0 Likes
on
0 Posts
Re: 1990 Mazda Miata
Didnt you JUST buy this before summer?
GLWS regaurdless...
GLWS regaurdless...
#3
Registered member
Thread Starter
Join Date: Aug 2007
Location: Richmond/Yorktown
Posts: 500
Likes: 0
Received 0 Likes
on
0 Posts
Re: 1990 Mazda Miata
Sure did. Bored with it hah. And i fixed most of the shit wrong with it.
Put over 10,000 miles on it hah.
Don't take this quick sale as the car is shitty. I haven't dogged the fuck outta it but i've driven it and it's definitely hella stable.
But thanks.
Put over 10,000 miles on it hah.
Don't take this quick sale as the car is shitty. I haven't dogged the fuck outta it but i've driven it and it's definitely hella stable.
But thanks.
#4
Registered member
Thread Starter
Join Date: Aug 2007
Location: Richmond/Yorktown
Posts: 500
Likes: 0
Received 0 Likes
on
0 Posts
Re: 1990 Mazda Miata
Up up up.
#5
Registered member
Thread Starter
Join Date: Aug 2007
Location: Richmond/Yorktown
Posts: 500
Likes: 0
Received 0 Likes
on
0 Posts
Re: 1990 Mazda Miata
Radiator fan wired to a switch and working great. Thermoswitch needs to be replaced for it to work off of engine temp.
Sat in traffic for around 25 minutes today in 98 degree weather and the temp needle didn't move a hair.
Possible trade on Wednesday.
Sat in traffic for around 25 minutes today in 98 degree weather and the temp needle didn't move a hair.
Possible trade on Wednesday.
#6
Registered member
Thread Starter
Join Date: Aug 2007
Location: Richmond/Yorktown
Posts: 500
Likes: 0
Received 0 Likes
on
0 Posts
Re: 1990 Mazda Miata
#7
Registered member
Thread Starter
Join Date: Aug 2007
Location: Richmond/Yorktown
Posts: 500
Likes: 0
Received 0 Likes
on
0 Posts
Re: 1990 Mazda Miata
Bump for another hot ass day.
And, pic of hood/bumper damage from PO.
And, pic of hood/bumper damage from PO.
#8
Officially Official
Join Date: Aug 2007
Location: Klofron
Posts: 1,980
Likes: 0
Received 0 Likes
on
0 Posts
Re: 1990 Mazda Miata
Wanna sell that roll bar?
#9
FUCKIN MAGNETS
Join Date: Nov 2002
Location: Norfolk
Posts: 22,585
Likes: 0
Received 0 Likes
on
0 Posts
Re: 1990 Mazda Miata
I miss this car
#10
Officially Official
Join Date: Aug 2007
Location: Klofron
Posts: 1,980
Likes: 0
Received 0 Likes
on
0 Posts
Re: 1990 Mazda Miata
its a good lookin ride. you should have kept it man!