97' Civic Fully built sleeved ls vtec
Name: Jon
Location:NOVA/PA Means of contact: 540-481-1287 Price: $7800 obo Description: Dont know where to start with this car ive owned it for close to two years now. I picked it up with a ITR swap guy fucked me motor was fucked after a week of owning THANKS just keep hiding KARMAS A BITCH anyway.....This car has been through alot since ive owned her i love it and take very good care of her and hope if i sell it someone else will also i had big plans for this car that were coming together cept the fact i have thieves all around me and parts just keep going missing :( So therefore ive lost interest and im sick of fighting with thieves when it comes to a build im in the middle of school at Wyotech and this is just too much for me right now so take a look let me know what you guys think i love opinions bump if viewed :) Thanks http://i1220.photobucket.com/albums/...psb1f27130.jpg Testingwaters hate to see her go Trades Possible just let me know Exterior - 1997 civic ex mileage unknown on body motor just barely broke in 2k miles max Carbon Fiber hood Carbon fiber fenders Carbon fiber trunk oem stanley sidemarkers Ctr lip rear lip si taillights Ctr rep headlights Interior - Red Bride ergo II Farenheit single din touch screen Si floor mats gauge bezel autometer boost gauge autometer oil psi aem wideband setup Red recaro door inserts red harness bar Takata drivers harness Itr shift boot Si Gauge cluster with low miles Xenon Hid HI/LO kit wink mirror Motor - B18B 85 mm darton sleeved 2,000 Miles on Motor 9.7:1 cp pistons w/ upgraded wrist pins Pauter x beam rods All new gates kevlar timing belt New water pump New type-r oil pump Moroso 5.5 oil pan w/ baffle B&R fitting breather kit Golden Eagle LSV kit NEW JE MLS Head gasket Polished ls crank Oldschool Innovative Motor mounts B18c1 Head Skunk2 Tuner stage 1 cams Skunk2 Oldschool red cam gears Skunk2 Valve springs+titanium retainers Skunk2 Alpha series valves Skunk2 Cam plug Port and polished port match hondata intake gasket port match eldebrock intake manifold port matched BBK 70mm throttle body ITR exhaust manifold 3angle valve job Greddy EVO2 exhaust MSD Distributor MSD coil ss MSD 6al ignition MSD super conductor 8.5mm wires Transmission - Very smooth much loved itr trans w/ vin Quafie lsd Stage 5 clutch mastes clutch kit stock flywheel Carbon coated syncros Suspension - Tein Mono Flex adjustable coilovers Function7 ITR conversion rear lcas BWR subframe brace Integra rear disc conversion Russel stainless steel brake lines Password jdm front drilled slotted rotors new brake pads 16" Konig countersteers no scratches nothing perfect condition Falken tires with maybe 300 miles on them I may be forgetting i few things... The Bad.... Theres is some flaws to the body that need some care Needs upper ball joint soon on passenger side clear coat flaking off rep headlights Needs inspection PASSENGER SIDE CF FENDER NOT INSTALLED IN PHOTOS http://i1220.photobucket.com/albums/...ps8636d899.jpg http://i1220.photobucket.com/albums/...ps04b0a71a.jpg http://i1220.photobucket.com/albums/...ps2a04b58a.jpg http://i1220.photobucket.com/albums/...ps4b348e69.jpg http://i1220.photobucket.com/albums/...ps69b3dfc8.jpg http://i1220.photobucket.com/albums/...ps6373ca1f.jpg http://i1220.photobucket.com/albums/...ps4dce6dcf.jpg http://i1220.photobucket.com/albums/...ps4ffb5133.jpg http://i1220.photobucket.com/albums/...psd7fc3a21.jpg http://i1220.photobucket.com/albums/...ps8ab04545.jpg Back before swap.... http://i1220.photobucket.com/albums/...ps76b24c09.jpg http://i1220.photobucket.com/albums/...ps12cd00d7.jpg SOME OLD PHOTOS http://i1220.photobucket.com/albums/...9-25182336.jpg http://i1220.photobucket.com/albums/...9-25182345.jpg http://i1220.photobucket.com/albums/...9-25182247.jpg WHEN I FIRST PURCHASED IT http://i1220.photobucket.com/albums/...0811151533.jpg http://i1220.photobucket.com/albums/...0811151555.jpg Also check other threads i have some turbo parts laying around im trying to get rid of let me know if interested: Precision 6162 BB T3 turbo fully built GSR head supertech race valvetrain ITR CAMS 2.5'' Intercooler piping w/ couplings and clamps Can make a return line for you |
97' Civic Fully built sleeved ls vtec
Damn you switches it up a few time love the engine bay though looks fresh!
|
Re: 97' Civic Fully built sleeved ls vtec
Originally Posted by miata_kid
(Post 8118055)
Damn you switches it up a few time love the engine bay though looks fresh!
|
[/QUOTE]
Thanks and yea im missing all kinds of pictures with different styles i was thinking on getting the BYS front bumper with carbonfiber lip[/QUOTE] Shit im not a honda head bro so ion no wat a BYS front bumper is,but GLWS |
Re: 97' Civic Fully built sleeved ls vtec
Bump
|
Re: 97' Civic Fully built sleeved ls vtec
Bump ttt
|
Re: 97' Civic Fully built sleeved ls vtec
bump
|
Re: 97' Civic Fully built sleeved ls vtec
damn sounds like all this is missing is a big turbo..
|
Re: 97' Civic Fully built sleeved ls vtec
Check thread
|
Re: 97' Civic Fully built sleeved ls vtec
Originally Posted by dylan
(Post 8120572)
damn sounds like all this is missing is a big turbo..
Originally Posted by sidewayz93
(Post 8120586)
Check thread
|
All times are GMT -8. The time now is 04:09 PM. |
© 2024 MH Sub I, LLC dba Internet Brands