355ci small block chevy with TH400 with 3800 stall converter. trade for lifted truck
11-05-2011, 01:45 PM
#1
Registered Member
Thread Starter
Join Date: Sep 2008
Posts: 468
Likes: 0
Received 0 Likes
on
0 Posts
355ci small block chevy with TH400 with 3800 stall converter. trade for lifted truck
Name: jeff
Location: charlottesville
Means of contact: 4349969942
Price: $5000
Description: I have a new never ran 355 small block Chevrolet. also a th400 transmission with a tci 3800 race stall converter. Good race or street strip setup, I was going to race motor with nitrous.
The engine
Keith black pistions 10.5:1 compression
eagle crank
afr aluminum heads(new valve job)
edelbrock intake manifold
lunati 550 lift cam
roller rockers
stud girdle
new black Chevrolet valve covers
red csr electric eater pump
new starter
HEI distributor with new cap and wires
7 at oil pan
B&M shifter to go with
I bought this motor like it was and had my engine builder go through it and check all clearances and make sure everything was okay. I have a receipt for $1000 from him, he checked everything, did a performance valve job, degreed cam. All new gaskets and valve seals. He said its a strong motor and could take a good shot of nitrous no problem, good valve clearance, not pushing any limits. He estimated about 500hp. I have receipts for everything, bottom to top, and transmission. Bottom end and trans/converter were bought in 2007 and have been sitting in a car since, approximately 500 miles on transmission .
Im asking $5000, i have between $8-9000 in receipts. looking for cash but would possibly be able to work out a trade on a lifted truck 4x4. Im looking for a Ford or Chevy with mud tires, approx. 38" mud tires, preferably not fuel injected
call or text 434-nine nine six 9942 can send pictures through phone
will post pictures tongiht
Location: charlottesville
Means of contact: 4349969942
Price: $5000
Description: I have a new never ran 355 small block Chevrolet. also a th400 transmission with a tci 3800 race stall converter. Good race or street strip setup, I was going to race motor with nitrous.
The engine
Keith black pistions 10.5:1 compression
eagle crank
afr aluminum heads(new valve job)
edelbrock intake manifold
lunati 550 lift cam
roller rockers
stud girdle
new black Chevrolet valve covers
red csr electric eater pump
new starter
HEI distributor with new cap and wires
7 at oil pan
B&M shifter to go with
I bought this motor like it was and had my engine builder go through it and check all clearances and make sure everything was okay. I have a receipt for $1000 from him, he checked everything, did a performance valve job, degreed cam. All new gaskets and valve seals. He said its a strong motor and could take a good shot of nitrous no problem, good valve clearance, not pushing any limits. He estimated about 500hp. I have receipts for everything, bottom to top, and transmission. Bottom end and trans/converter were bought in 2007 and have been sitting in a car since, approximately 500 miles on transmission .
Im asking $5000, i have between $8-9000 in receipts. looking for cash but would possibly be able to work out a trade on a lifted truck 4x4. Im looking for a Ford or Chevy with mud tires, approx. 38" mud tires, preferably not fuel injected
call or text 434-nine nine six 9942 can send pictures through phone
will post pictures tongiht
Thread
Thread Starter
Forum
Replies
Last Post
Foc-US2K
Engine / Exhaust / Drivetrain
0
12-07-2010 06:20 AM
Gixxer2003
Engine / Exhaust / Drivetrain
8
10-18-2009 08:56 AM