My STi is finally back!
#1
Damn street racers
Thread Starter
Join Date: Aug 2004
Location: richmond VA
Posts: 791
Likes: 0
Received 0 Likes
on
0 Posts
My STi is finally back!
my sti is finally back to where i want it after the stock block took a shit on me. the car was tuned up at agile auto in maryland they did the motor work on my car.
Power mods.
Turbo Forced performance FP Red (garrett Gt35)
Agile stage 1 built short block
stock heads
helix 860cc injectors
buscher dual 255s
aps fuel rails
aeromotive FPR
ultimate racing uppipe and 38mm tial
hks Dp
Cobb catback
DMH Cutout
gruppe-s ver 2 header
ssac fmic
aem 3.5 bar map sensor
aem AIT sensor
Aquamist HFS-5
turbosmart eboost 2
AEM EMS
And the most important mod a kick A** tune by Hill!
First we tuned the car on meth and 93 octane on about 25.5, 26 psi! the results were amazing i dont have the dyno chart for this map but i belive it was
471whp and 456 ft/lbs
Now on to the good stuff we put in the Q16 and opened the cutout and tuned up the boost to right at 29psi (didnt want to push the stock sleeves to hard).
the results were amazing we finished up at...
536whp and 500ft/lbs!
we had the power up in the 550 range but didnt want to risk anything so i had him lower the boost a little but i know i have that little extra power on tap if i need it.
Thanks again to all the great people at agile,
Paul
Edit just so everyone knows the graph says flywheel power but it is wheel hp thats just what all dynopak dynos say at the top. no sae correction was added
Here is another dyno graph hill sent me to compare the pump+meth map and my race gas map.
i also posted this on page 3
Power mods.
Turbo Forced performance FP Red (garrett Gt35)
Agile stage 1 built short block
stock heads
helix 860cc injectors
buscher dual 255s
aps fuel rails
aeromotive FPR
ultimate racing uppipe and 38mm tial
hks Dp
Cobb catback
DMH Cutout
gruppe-s ver 2 header
ssac fmic
aem 3.5 bar map sensor
aem AIT sensor
Aquamist HFS-5
turbosmart eboost 2
AEM EMS
And the most important mod a kick A** tune by Hill!
First we tuned the car on meth and 93 octane on about 25.5, 26 psi! the results were amazing i dont have the dyno chart for this map but i belive it was
471whp and 456 ft/lbs
Now on to the good stuff we put in the Q16 and opened the cutout and tuned up the boost to right at 29psi (didnt want to push the stock sleeves to hard).
the results were amazing we finished up at...
536whp and 500ft/lbs!
we had the power up in the 550 range but didnt want to risk anything so i had him lower the boost a little but i know i have that little extra power on tap if i need it.
Thanks again to all the great people at agile,
Paul
Edit just so everyone knows the graph says flywheel power but it is wheel hp thats just what all dynopak dynos say at the top. no sae correction was added
Here is another dyno graph hill sent me to compare the pump+meth map and my race gas map.
i also posted this on page 3
Last edited by trbowrx; 11-20-2008 at 07:32 PM.
#4
Damn street racers
Thread Starter
Join Date: Aug 2004
Location: richmond VA
Posts: 791
Likes: 0
Received 0 Likes
on
0 Posts
#10
Damn street racers
Thread Starter
Join Date: Aug 2004
Location: richmond VA
Posts: 791
Likes: 0
Received 0 Likes
on
0 Posts