HELP! INSTALL AEM WIDEBAND WITH NEPTUNE RTP 95GSR!!
#1
Registered member
Thread Starter
Join Date: Jun 2007
Location: Fredericksburg
Posts: 680
Likes: 0
Received 0 Likes
on
0 Posts
HELP! INSTALL AEM WIDEBAND WITH NEPTUNE RTP 95GSR!!
Travis
95 acura integra gsr
neptune rtp
aem uego wideband
ok so i have jut recived my aem uego wideband kit
and am seeking some help on the wiring part of the installation
the car is obd1 using a p28 with neptune demon rtp
neptune has 2 output signal settings 1 that has to be wired into the wideband but i canot locate a good enough digram to find witch wire i should tap into on the harness side
if anyone knows of a good DIY they have seen on installing this that would be awesome or just any insight would help
thanks vadriven!!
95 acura integra gsr
neptune rtp
aem uego wideband
ok so i have jut recived my aem uego wideband kit
and am seeking some help on the wiring part of the installation
the car is obd1 using a p28 with neptune demon rtp
neptune has 2 output signal settings 1 that has to be wired into the wideband but i canot locate a good enough digram to find witch wire i should tap into on the harness side
if anyone knows of a good DIY they have seen on installing this that would be awesome or just any insight would help
thanks vadriven!!
#4
Re: HELP! INSTALL AEM WIDEBAND WITH NEPTUNE RTP 95GSR!!
im looking to do the same thing but im using hondata. so far, from what i gathered, d14 is o2 signal and you can also use d10, b6 and d12 for other sensors that outputs 0-5v.
02 input D14
ELDinput D10
B6 Input
EGR Lift input D12
what im confused about is neptune says 4 inputs but hondata says 2 inputs. does that mean neptune can only read the 4 factory ecu inputs and the s300 adds another 2?
02 input D14
ELDinput D10
B6 Input
EGR Lift input D12
what im confused about is neptune says 4 inputs but hondata says 2 inputs. does that mean neptune can only read the 4 factory ecu inputs and the s300 adds another 2?
#5
Registered member
Join Date: Apr 2008
Location: Virginia Beach
Posts: 259
Likes: 0
Received 0 Likes
on
0 Posts
Re: HELP! INSTALL AEM WIDEBAND WITH NEPTUNE RTP 95GSR!!
Use D10 for the your wideband input because it is 5v where as d14 is only something like 3.XX volts. The help section in neptune will show you how to set up the voltage values in neptune.
#6
Re: HELP! INSTALL AEM WIDEBAND WITH NEPTUNE RTP 95GSR!!
are both neptune and hondata the same for reading the 4 analog inputs? neptune says "4 programmable analog inputs" but hondata says "2 analog inputs for wideband, egts etc"
is hondata capable of reading all 4 or does it mean its adding another 2 inputs?
is hondata capable of reading all 4 or does it mean its adding another 2 inputs?
#7
Registered member
Join Date: Apr 2008
Location: Virginia Beach
Posts: 259
Likes: 0
Received 0 Likes
on
0 Posts
Re: HELP! INSTALL AEM WIDEBAND WITH NEPTUNE RTP 95GSR!!
No, it means exactly what it says. Neptune has 4 programmable inputs and hondata has only 2 programmable inputs.
Thread
Thread Starter
Forum
Replies
Last Post
RedStar101
Engine / Exhaust / Drivetrain
0
03-07-2009 07:41 AM