Anthony
Virginia Beach
PM me or text 904-422-6402

As some may know, my Civic Si is totaled but most of the car is salvageable. I am posting a list of what I am gonna be parting out of this car just to see who all is interested. I should get the car back in a little over a week or so once the claim gets finalized. So here it goes.

***EVERY PART IN THIS LIST HAS SEEN ROUGHLY 900 MILES***

***ALL MY PRICES ARE FIRM SO DONT ASK FOR A LOWER PRICE OR TRADES, THANK YOU***

Here are pics of the parts before they were installed to get a rough idea until i pull the motor out

http://www.honda-tech.com/showthread.php?t=2367730

LS/VTEC Longblock - NO I WILL NOT SELL ANYTHING SEPARATE

Everything has about 900 miles on it. Doesnt burn oil, no blow by. She's solid!!!
B18B Block stock sleeve 81.55mm bore by Abacus
Polished and Balanced LS Crank
Clevite Bearings
Eagle Rods
CP 9:1 Pistons Compression is 185-187 across the board
Type R oil pump
GSR Water Pump
GSR Timing Belt
GSR Headgasket
LS Thermostat
GSR HEAD
GSR Cams
Skunk 2 Cam Gears
Supertech Valvetrain and Valves
Stock dizzy with new coil and rotor
ARP Headstuds

$1900 FIRM not a penny lower - I spent $2600 building this NOT including my labor
-------------------------------------------------------------------------------------------------------------------
AFI Turbo Kit I will part out. Not sure on prices yet.

$850 - AFI Top Mount Manifold
750 - T3/T67 H.O with P trim wheel .63AR
250 - 3" Downpipe with flex section / testpipe to fit kteller exhaust
200 - Intercooler 28x11x3
30 - All couplers and t-bolt clamps

$2,650 FIRM!
-------------------------------------------------------------------------------------------------------------------
280 - RC 1000cc Injectors
60 - BDL Fuel rail
80 - Feed/Return Fuel line kit
100 - Aeromotive FPR 13109
20 - NGK wires
20 - Fast Turbo vacuum manifold
50 - Golden Eagle Sandwich plate adapter with fittings
300 - KTeller Full SS 3" Exhaust for EK
10 - B&M Fuel pressure gauge
250 - Edelbrock Victor X Intake manifold 70mm
140 - Skunk 2 Throttle Body 70mm
300 - Hasport STK mounts
40 - Autometer 3 pod pillar
40 - GM 3 bar map sensor w/pigtail
300 - Competition Clutch 0420 with upgraded pressure plate
80 - Exedy 8-9 lb flywheel
50 - MSD Blaster Coil and Cap
30 - Autometer Oil Pressure Gauge
50 - Skunk 2 Shift Knob
650 - Quaife LSD
150 - GSR tranny with 4.7 FD - needs new 1-2 sleeve set.

I may have more thats not listed but this is what I have so far.

 

pm'd

 

Pictures are a must. 1 good engine bay shot should work for now if you have one.

The catch can is what I'm interested in.

 

dibs on the skunk2 short shifter and shift knob

 

You can kinda see the catch can in the corner in front of the battery. Those 2 lines off the valve cover are running to it and a return line under the box runs straight to the ground. I have the fitting for the block but i decided against using it.

 

sorry to hear about your car but look you need to work on those prices some

 

bump for/was a nice setup atleast sounded like it was never saw u driving around

 

I want the catch can and lines, hit me up....

 

wondering if you would part out the whole front end???
lmk pm me.

 

Explain to me why i need to work on these prices??? Every part has barely 900 miles on them Why would i buy brand new parts, barely use them, then discount them 50%?? not happening. If this stuff sells then it sells, if it doesnt then it doesnt.