konatownn

Colin Pascoe

Cell: 757-292-0569 < Fastest response (No answer, Leave a brief message)
Email: kewalows@hotmail.com
Location: Norfolk VA

*Will consider trades + Cash. I'd prefer a little accord, corolla, ect. For a Daily.

*$10,000 OR BEST OFFER ***$8,500 OBO (11/9)


SOLD!!





Joining the Air force soon, & need to let go of my baby. I've owned it for about three years now, along with two others. It made a little over 300whp on 15psi two weeks ago at MRD. Compression is great, 160 across. I haven't ran anything other then 93 octane.


1991 240sx hatchback
-Sun roof
-Black carpet
-Power windows, locks, mirrors
-No AC
-No Power steering
-New break pads
-New clutch slave & master cylinder
-180sx LSD


Exterior;
-Pig nose (From an 89) w/ lip
-Tint done at TNT in Virginia Beach a few months ago

Interior;
-S14 seats
-Sony cd player w/ Ipod cable in the glove box
-Base model steering wheel (no cruise control buttons)
-Boost & oil pressure gauge
-New Battery in the back


Fresh FULLY rebuilt Red top SR20DET (5k miles) (built by Greaser at MRD);
-Cp Pistons 86.5mm/9:1
-Eagle rods
-Clevite P-Series rod & main bearings
-Cometic HG
-New Water pump
-Brian Crower Springs and Titanium Retainers
-ARP Main & Head studs
-OEM Complete Timing Chain Kit
-Inspected oil pump
-GReddy Rocker Arms Stoppers
-Front & rear main seals
-Intake Gasket
-Valve Seals

MACHINE WORK
-Bore/Hone/Deck
-Polished balanced crank
-Cut Valves

Set-up;
-Garrett T3/T04E turbo w/ stage 3 wheel (no play, side-side/in-out)
-Equal length tubular manifold
-Metal "Mr Gasket" exhaust gasket
-Tial 40mm wastegate
-Deatschwerks 680cc injectors
-Walbro 255 Fuel Pump
-300zx Fuel Filter
-Enthalpy ECU tune
-Z32 MAF
-Custom IC piping (MRD)
-Custom 3' Down pipe (MRD)
-Test pipe with full 3' Exhaust (Not too loud)
-Trust Intercooler
-Turbo XS RFL Blow off valve
-Manual Hallman Pro Boost Controller
-New engine harness
-AEM dry flow filter
-Blitz DTT DCIV; turbo timer
-16' electric fan
-Koyo Radiator
-Heater hoses http://www.enjukuracing.com/heater-h...et-p-6500.html
-Catch can
-Megan hardened motor & tranny mounts
-ISIS oil pan
-Aluminum One-piece Driveshaft
-SPEC stage 3 clutch kit
-THICK turbo heat blanket http://www.enjukuracing.com/turbo-he...et-p-6685.html
-Samco hoses
-Re-surfaced fly wheel


Suspension;
-Megan street coilovers 32 way adj.
-Suspension Techniques front(1 1/8) & rear(13/16) sway bars
-Tien tie rods & ends w/ spacer for increased turning radius
-Nismo front brace
-Megan tension rods
-Megan traction links
-Megan RUCA's
-Megan rear toe rods
-New OEM FLCA's
-Megan front strut tower bar
-Cusco rear triangle bar

konatownn

I get complements all the time about how clean & well maintained the car looks. With a paint job and some wheels, this car would be FLAWLESS. Runs & cruses very quiet, not a rattle trap, Very "Daily-Drivable"!

1sickmcx

its a very nice pignose bro.....its looks good.....glws.

IslandBoy

let me get that piggy lip braaaaaaaaaaaaaah

konatownn

Thanks! I really hate to sell it. But with my situation its best for me to let go





I know a dude that might sell you his, besides a few zip-tie holes its straight! give me a shout

konatownn

konatownn

konatownn

F R E S H

konatownn

TTT

konatownn

Did another Compression test. 160 In all four