eg hatch turbo, Look!!!!
#1
Registered member
Thread Starter
Join Date: Feb 2009
Posts: 378
Likes: 0
Received 0 Likes
on
0 Posts
eg hatch turbo, Look!!!!
PLEASE DELETE
Name: mike
Location: crozet
Means of contact: pm, post to thread
Price: 10k best offer or trades
more pics coming soon, manager isnt working for some reason
Description: Hi, I have been working on this project for two years and lost interest and money at the same time. The car is very close to being complete and only needs a few more thing to make this an nice ride. This car properly tuned should produce 600 plus hp. The odometer reads 181k miles but its incorrect since the cluster has been changed several times. The paint job was done by a previous owner and I was told it cost over 9k to have it done. The flames are out lined and have cross hatches that were hand painted. All the paint is house of colors. The rear bumper needs to be repainted and the hood has one place in it that i can provide a picture of if necessary. The rag top is fully functional but it does have some minor cosmetic issues around the edges where it was installed, that i can also provide pictures for. The car starts up and runs but I have not drove it because im worried about damaging the engine without it being tuned. The upgrades are as followed:
Engine and trans.
b20 sleeved block with 87mm bore
eagle crank
eagle rods
wiesco pistons (9:1 compression)
type r oil pump
new oil pickup tube
acl race bearings (rod and mains)
moraso 6 quart oil pan
type r oil cooler
type t crank pulley (aluminum)
all new felpro gaskets
b16 head (port and polished)
valve springs
new valves
blox type B cams
vision cam gears
all new from honda lma's
blox intake manifold (port matched)
blox 70mm throttle body
omni tps
fitec 4 bar map
Holley fuel rail
rc 1000cc injectors (resistor wired in)
summit fuel pressure gauge
custom b&g fuel filter with braided fuel lines ( stock filter housing eliminated)
kms map adapter
tenzo r valve cover (moon cut outs)
new oil cap
oil catch can
new vtec solenoid
gates racing timing belt
new Honda tensioner
new water pump
custom made head gasket from ceramic gaskets
luv fab T4 turbo manifold
46mm waste-gate (custom dump tube)
Straight T4 or to4 60-1.15 turbo made by Garrett
turbo heat shield
braided oil return and supply
aem dry flow air filter
three inch v-band down pipe
custom made aluminum radiator
custom radiator hoses
eric's racing fuel pressure regulator
braided vtec oil feed line
summit racing radiator overflow tank
nrg torque damper
energy suspension torque mount inserts
rear engine mount insert
Hasport top engine and trans mounts
ngk iridium spark plugs
greddy type s blow off valve
movable bov flange
3 ply silicone inter cooler couplings
3 inch inter cooler pipe
600 hp delta fin inter cooler
all new T-bolt clamps
$1500 in engine machine work
full msd (6al box, blaster 2 coil, wires) still have the box
500 hp axles
Integra ls tranny rebuilt
phantom grip lsd
act stage 4 clutch
act flywheel
arp head studs
arp flywheel and clutch bolts
the engine has been painted with house of colors heat treated pained to match the exterior.
hondata s300 in obd1 ecu
exterior
9k paint job
wings west lower spoiler
aftermarket mirrors
rag top
17 inch effect wheels (black and polish)
205/45/17 rear tires
225/45/17 yoko street drag radials on the front
amber corner lights
em1 style rear tail lights
amber side marker lights
suspension
tokico struts and shocks
skunk lowering springs
skunk front and rear camber kit
traction bars
every ball joint brand new
rear upper and lower strut bars
interior
roll cage painted to match the car (welded in)
rs steering wheel
3-carbon gauge pod
ek front and rear seats
the gauge bezel is painted purple
aftermarket pedals
shift boot
Pictures:
Name: mike
Location: crozet
Means of contact: pm, post to thread
Price: 10k best offer or trades
more pics coming soon, manager isnt working for some reason
Description: Hi, I have been working on this project for two years and lost interest and money at the same time. The car is very close to being complete and only needs a few more thing to make this an nice ride. This car properly tuned should produce 600 plus hp. The odometer reads 181k miles but its incorrect since the cluster has been changed several times. The paint job was done by a previous owner and I was told it cost over 9k to have it done. The flames are out lined and have cross hatches that were hand painted. All the paint is house of colors. The rear bumper needs to be repainted and the hood has one place in it that i can provide a picture of if necessary. The rag top is fully functional but it does have some minor cosmetic issues around the edges where it was installed, that i can also provide pictures for. The car starts up and runs but I have not drove it because im worried about damaging the engine without it being tuned. The upgrades are as followed:
Engine and trans.
b20 sleeved block with 87mm bore
eagle crank
eagle rods
wiesco pistons (9:1 compression)
type r oil pump
new oil pickup tube
acl race bearings (rod and mains)
moraso 6 quart oil pan
type r oil cooler
type t crank pulley (aluminum)
all new felpro gaskets
b16 head (port and polished)
valve springs
new valves
blox type B cams
vision cam gears
all new from honda lma's
blox intake manifold (port matched)
blox 70mm throttle body
omni tps
fitec 4 bar map
Holley fuel rail
rc 1000cc injectors (resistor wired in)
summit fuel pressure gauge
custom b&g fuel filter with braided fuel lines ( stock filter housing eliminated)
kms map adapter
tenzo r valve cover (moon cut outs)
new oil cap
oil catch can
new vtec solenoid
gates racing timing belt
new Honda tensioner
new water pump
custom made head gasket from ceramic gaskets
luv fab T4 turbo manifold
46mm waste-gate (custom dump tube)
Straight T4 or to4 60-1.15 turbo made by Garrett
turbo heat shield
braided oil return and supply
aem dry flow air filter
three inch v-band down pipe
custom made aluminum radiator
custom radiator hoses
eric's racing fuel pressure regulator
braided vtec oil feed line
summit racing radiator overflow tank
nrg torque damper
energy suspension torque mount inserts
rear engine mount insert
Hasport top engine and trans mounts
ngk iridium spark plugs
greddy type s blow off valve
movable bov flange
3 ply silicone inter cooler couplings
3 inch inter cooler pipe
600 hp delta fin inter cooler
all new T-bolt clamps
$1500 in engine machine work
full msd (6al box, blaster 2 coil, wires) still have the box
500 hp axles
Integra ls tranny rebuilt
phantom grip lsd
act stage 4 clutch
act flywheel
arp head studs
arp flywheel and clutch bolts
the engine has been painted with house of colors heat treated pained to match the exterior.
hondata s300 in obd1 ecu
exterior
9k paint job
wings west lower spoiler
aftermarket mirrors
rag top
17 inch effect wheels (black and polish)
205/45/17 rear tires
225/45/17 yoko street drag radials on the front
amber corner lights
em1 style rear tail lights
amber side marker lights
suspension
tokico struts and shocks
skunk lowering springs
skunk front and rear camber kit
traction bars
every ball joint brand new
rear upper and lower strut bars
interior
roll cage painted to match the car (welded in)
rs steering wheel
3-carbon gauge pod
ek front and rear seats
the gauge bezel is painted purple
aftermarket pedals
shift boot
Pictures:
Last edited by sweethatch1866; 04-07-2011 at 04:06 PM. Reason: keeping it for now
#6
Registered member
Join Date: Mar 2008
Location: Richmond,VA
Posts: 2,444
Likes: 0
Received 0 Likes
on
0 Posts
Re: eg hatch turbo, Look!!!!
the car will deffinatly need repainting...any papers on the mods and build?..it should roll out once tunned to be honest and wouldnt be a bad car if the paint wasn't so off the wall but to each's own...glws bro..
#8
Registered member
Thread Starter
Join Date: Feb 2009
Posts: 378
Likes: 0
Received 0 Likes
on
0 Posts
Re: eg hatch turbo, Look!!!!
I got some of the bigger receipts not all of them. Like I said i been working on it for two years. Its one of them cars,,, you either like it or you dont. Honestly Im not crazy about the paint it but its an eye catcher. same goes for the rag top.