built b20vtec all motor crx for lifted 4x4
#1
the street alchemist
Thread Starter
Join Date: Jan 2007
Location: hampton
Posts: 127
Likes: 0
Received 0 Likes
on
0 Posts
built b20vtec all motor crx FS
rob
hampton, va
757-254-7816
$3500 Or Trade
I got this car a couple months ago off another member on here. Since then I've fully rebuilt the entire motor w/ receipts. I'm done with hondas and tuner imports, and I figure since i'm moving out to the country I'll go back to a mud truck. my loss is someone else's gain, this car has over 8k invested. Serious people only I am willing to give test rides with the buyer as the passenger but i can't risk someone destroying my investment. unless i have cash or collateral. no low ballers please and if you have any negative comments try to refrain from commenting.
B20b4
Ctr head ported and polished
Skunk 2 stage2 cams
Type r intake manifold ported
Skunk 2 springs and retainers
3 angle valve job
Spr fuel rail
B&m regulator
Pwr 1/4 radiator
4-1 professional custom exhaust
Arp head studs
Arp 2000 rod studs
Battery relocation kit with switch and circuit breaker
550 cc injectors
Walbro 255 fuel pump
sparco steering wheel
Led digital shift light with rpm display
1/4 inch wheel spacers
Arp wheel studs
Endyne breather system
Golden eagle vtec conversion
Je 12.5 : 1 pistons
Eagle h beam rods
Balanced crank
All color coded and blueprinted bearings
Ys1 transmission (absolutely no grinds or rattles)
10 lb flywheel with exedy stage 1 clutch
Hondata s300 version2 and dyno tuned with launch and burnout control
Data logging hookups
new water pump
New oil pump
New timing belt and tensioner
New axles
All new gaskets
New sensors (coolant, ait, Tps, map..etc.)
Obd1 conversion by rywire
Avid traction bars
Ground control coilovers kyb struts
Fresh build less than 800 miles, I can even compression/leak down test it in front of you
hampton, va
757-254-7816
$3500 Or Trade
I got this car a couple months ago off another member on here. Since then I've fully rebuilt the entire motor w/ receipts. I'm done with hondas and tuner imports, and I figure since i'm moving out to the country I'll go back to a mud truck. my loss is someone else's gain, this car has over 8k invested. Serious people only I am willing to give test rides with the buyer as the passenger but i can't risk someone destroying my investment. unless i have cash or collateral. no low ballers please and if you have any negative comments try to refrain from commenting.
B20b4
Ctr head ported and polished
Skunk 2 stage2 cams
Type r intake manifold ported
Skunk 2 springs and retainers
3 angle valve job
Spr fuel rail
B&m regulator
Pwr 1/4 radiator
4-1 professional custom exhaust
Arp head studs
Arp 2000 rod studs
Battery relocation kit with switch and circuit breaker
550 cc injectors
Walbro 255 fuel pump
sparco steering wheel
Led digital shift light with rpm display
1/4 inch wheel spacers
Arp wheel studs
Endyne breather system
Golden eagle vtec conversion
Je 12.5 : 1 pistons
Eagle h beam rods
Balanced crank
All color coded and blueprinted bearings
Ys1 transmission (absolutely no grinds or rattles)
10 lb flywheel with exedy stage 1 clutch
Hondata s300 version2 and dyno tuned with launch and burnout control
Data logging hookups
new water pump
New oil pump
New timing belt and tensioner
New axles
All new gaskets
New sensors (coolant, ait, Tps, map..etc.)
Obd1 conversion by rywire
Avid traction bars
Ground control coilovers kyb struts
Fresh build less than 800 miles, I can even compression/leak down test it in front of you
Last edited by S-Alchemist; 10-30-2012 at 08:01 PM.
#10
the street alchemist
Thread Starter
Join Date: Jan 2007
Location: hampton
Posts: 127
Likes: 0
Received 0 Likes
on
0 Posts
A far a what type of truck, nothing with less then 35 inch tires. Not willing to trade for a truck with stock suspension with blocks It made right at 220 whp on mid grade fuel.
My contact number is 7572547816
My contact number is 7572547816