Turbo kit Garrett t3/t4 57 trim
02-20-2009, 10:45 AM
#1
Registered Member
Thread Starter
Join Date: Oct 2004
Location: Charlottesville,VA
Posts: 123
Likes: 0
Received 0 Likes
on
0 Posts
Turbo kit Garrett t3/t4 57 trim
I’m selling my turbo setup from my 92LS w/b18c1. I never had it professionally tuned or dyno’d but I imagine it would net 280-300hp on a b-series vtec depending on boost level. Looking to get $900 shipped obo
Garrett 57 Trim t3/t4 Part# 466159-5003 Model# TA3405
Compressor Specs:
- T04E housing 2-3/4" inlet 2" outlet
- 57 trim T04E compressor wheel 2.23/2.95 45lb/min
Turbine Specs:
- T31 4 bolt outlet turbine housing .63A/R ratios
- 76 trim T31 turbine wheel (stage 3)
Comes with pretty much everything except the DSM 450 injectors unless I can find a set of GSR ones to trade out.
- Turbo( has about 2 months of use on 7lbs) it was $550 new
- Unknown brand cast manifold
- Tial 38mm waste gate with .5bar spring. I’ll also throw in a 10lb spring as well
- HKS SSQV(style) BOV
- Vacuum manifold with all vacuum hose needed
- Neutron Boost gauge
- 2.5 downpipe with 4 bolt flange
- Dump tube(needs to be rewelded at flange)
- Intercooler(28x6.5x2.5)painted black on one side
- Intercooler piping
- Oil restrictor with oil feed lines and oil return flange
- Xenocron DIY 3bar map sensor. Needs to be resoldered and sealed
- Megan Racing Oil Pressure Gauge with sending unit
Thanks for looking
Garrett 57 Trim t3/t4 Part# 466159-5003 Model# TA3405
Compressor Specs:
- T04E housing 2-3/4" inlet 2" outlet
- 57 trim T04E compressor wheel 2.23/2.95 45lb/min
Turbine Specs:
- T31 4 bolt outlet turbine housing .63A/R ratios
- 76 trim T31 turbine wheel (stage 3)
Comes with pretty much everything except the DSM 450 injectors unless I can find a set of GSR ones to trade out.
- Turbo( has about 2 months of use on 7lbs) it was $550 new
- Unknown brand cast manifold
- Tial 38mm waste gate with .5bar spring. I’ll also throw in a 10lb spring as well
- HKS SSQV(style) BOV
- Vacuum manifold with all vacuum hose needed
- Neutron Boost gauge
- 2.5 downpipe with 4 bolt flange
- Dump tube(needs to be rewelded at flange)
- Intercooler(28x6.5x2.5)painted black on one side
- Intercooler piping
- Oil restrictor with oil feed lines and oil return flange
- Xenocron DIY 3bar map sensor. Needs to be resoldered and sealed
- Megan Racing Oil Pressure Gauge with sending unit
Thanks for looking
03-01-2009, 05:48 PM
#5
Registered Member
Thread Starter
Join Date: Oct 2004
Location: Charlottesville,VA
Posts: 123
Likes: 0
Received 0 Likes
on
0 Posts
03-13-2009, 03:01 PM
#6
Registered Member
Join Date: Dec 2007
Posts: 1,059
Likes: 0
Received 0 Likes
on
0 Posts
