SR20 Custom Oil Cooler for S13 & S14 & Custom Chuki intakes
02-27-2013, 11:27 AM
#1
Registered member
Thread Starter
Join Date: Nov 2010
Posts: 70
Likes: 0
Received 0 Likes
on
0 Posts
SR20 Custom Oil Cooler for S13 & S14 & Custom Chuki intakes
Name: Bumnah
Location: Central VA
Means of contact: email: forums at bumnah dot com
Price: $650 or $550. Details below
Oil cooler:
Used for less than 500 miles.
Tomei Oil block for SR20 - NEW
Custom BMRS lines -10 lines tested at 300 psi
TRU-Cool 8x11x1-1/2" oil cooler
Canton Mecca racing remote oil filter
CUSTOM Carbon fiber ducting with dual 3" inlets.
Notes: The system was designed to minimize oil lines as much as possible to reduce the strain on the oil pump. This is a very complete setup! This can go in either S13 or S14. This is a custom setup, so there will be come custom work required for you to install it. Buyer be warned.
S13 Chuki bumper intakes:
Custom intake for the later model s13 front bumper.
Bolt these to the oem intakes ducts on the bumper, and run the hoses to an oil cooler or your brakes, or anything else.
These can used in any application you can think of. The material they are made of is similar to nylon 6. They were made on a selective laser sintering machine.
Here is a video of a laser sintering machine:
http://youtu.be/SVkUwqzjGJY
Each intake has two 3" outlets. You can run each 3" outlet to whatever you like. There is a center line dividing the 3" outlets. There is also a line running around the out side of the intake to help keep the hoses attached. Quality, one off piece. Cost of manufacturing an item like this is significantly higher than the sale price. This is for a pair of intakes, so you get it for both the left and right side. One side was created, and then mirrored for the opposite side. Never used, never tested, no warranty expressed or implied.
Pictures:
Full oil cooler kit with optional intake ducts.
Full kit assembled. Tomei oil block not pictured, but included. Intake ducts are optional
Back of the heat exchanger, with CF duct mounted.
Kit installed.
How the heat exchanger sits.
Close up of the filter mounted.
Mounting the CF duct to the heat exchanger.
CF duct on the exchanger.
How they're mounted.
Another angle
Yet another angle
From the back.
Sweet ass graphics!
The pair for sale.
PRICING:
Oil cooler kit with intake ducts, $500 shipped in the 48 states.
Oil cooler kit without intake ducts, $400 shipped in the 48 states.
NOTE: CF duct comes with the heat exchange regardless.
Email is the best way to reach me. forums at bumnah dot com
Shipped within 24 hours of payment.
Location: Central VA
Means of contact: email: forums at bumnah dot com
Price: $650 or $550. Details below
Oil cooler:
Used for less than 500 miles.
Tomei Oil block for SR20 - NEW
Custom BMRS lines -10 lines tested at 300 psi
TRU-Cool 8x11x1-1/2" oil cooler
Canton Mecca racing remote oil filter
CUSTOM Carbon fiber ducting with dual 3" inlets.
Notes: The system was designed to minimize oil lines as much as possible to reduce the strain on the oil pump. This is a very complete setup! This can go in either S13 or S14. This is a custom setup, so there will be come custom work required for you to install it. Buyer be warned.
S13 Chuki bumper intakes:
Custom intake for the later model s13 front bumper.
Bolt these to the oem intakes ducts on the bumper, and run the hoses to an oil cooler or your brakes, or anything else.
These can used in any application you can think of. The material they are made of is similar to nylon 6. They were made on a selective laser sintering machine.
Here is a video of a laser sintering machine:
http://youtu.be/SVkUwqzjGJY
Each intake has two 3" outlets. You can run each 3" outlet to whatever you like. There is a center line dividing the 3" outlets. There is also a line running around the out side of the intake to help keep the hoses attached. Quality, one off piece. Cost of manufacturing an item like this is significantly higher than the sale price. This is for a pair of intakes, so you get it for both the left and right side. One side was created, and then mirrored for the opposite side. Never used, never tested, no warranty expressed or implied.
Pictures:
Full oil cooler kit with optional intake ducts.
Full kit assembled. Tomei oil block not pictured, but included. Intake ducts are optional
Back of the heat exchanger, with CF duct mounted.
Kit installed.
How the heat exchanger sits.
Close up of the filter mounted.
Mounting the CF duct to the heat exchanger.
CF duct on the exchanger.
How they're mounted.
Another angle
Yet another angle
From the back.
Sweet ass graphics!
The pair for sale.
PRICING:
Oil cooler kit with intake ducts, $500 shipped in the 48 states.
Oil cooler kit without intake ducts, $400 shipped in the 48 states.
NOTE: CF duct comes with the heat exchange regardless.
Email is the best way to reach me. forums at bumnah dot com
Shipped within 24 hours of payment.
Last edited by Bumnah; 04-11-2013 at 05:20 PM.
02-28-2013, 09:20 AM
#3
-RepLegion
Join Date: Apr 2010
Location: Newport News/ NC Lake Gaston
Posts: 2,166
Likes: 0
Received 0 Likes
on
0 Posts
Re: SR20 Custom Oil Cooler for S13 & S14 & Custom Chuki intakes
man nice product.But to be honest it looks as though your a commercial seller and not a private seller. If that's the case please pay to advertise and im sure you will get a ton of sales threw our website.
02-28-2013, 11:32 AM
#4
Registered member
Thread Starter
Join Date: Nov 2010
Posts: 70
Likes: 0
Received 0 Likes
on
0 Posts
Re: SR20 Custom Oil Cooler for S13 & S14 & Custom Chuki intakes
Thanks.
I'm not a commercial seller. These are parts I made for myself. I've since sold my 240sx (back in 2010).
I am not affiliated with any shop, or any company that deals with performance parts for cars.
I'm not a commercial seller. These are parts I made for myself. I've since sold my 240sx (back in 2010).
I am not affiliated with any shop, or any company that deals with performance parts for cars.
03-01-2013, 09:03 AM
#5
-RepLegion
Join Date: Apr 2010
Location: Newport News/ NC Lake Gaston
Posts: 2,166
Likes: 0
Received 0 Likes
on
0 Posts
Re: SR20 Custom Oil Cooler for S13 & S14 & Custom Chuki intakes
Looking at the quality of these parts you should really go into production and start selling these. This is some awesome stuff man.
03-02-2013, 03:19 AM
#6
Registered member
Thread Starter
Join Date: Nov 2010
Posts: 70
Likes: 0
Received 0 Likes
on
0 Posts
Re: SR20 Custom Oil Cooler for S13 & S14 & Custom Chuki intakes
Again, thanks for the kind words.
There's no money in a business like this. I've had these two pairs of late model s13 bumper intakes for 2 years for that exact reason.
Parts will for sale people!
There's no money in a business like this. I've had these two pairs of late model s13 bumper intakes for 2 years for that exact reason.
Parts will for sale people!