Garrett Turbo $250 InlinePRO injectors $150 InlinePRO Intake manifold RARE!
#1
Garrett Turbo $250 InlinePRO injectors $150 InlinePRO Intake manifold RARE!
I beleive this was possibly a custom thing, and it came off a InlinePRO turbo kit- This is good for middle 400whp
60 ttrim compressor, 83 turbine according to my calculations (I measured everything)
Shaft spins free, but as with any used turbo, a rebuild would not hurt ya know?
Very little shaft play( Definately within spec)
I even took a video of it- check it out so you can get a better picture of what you are dealing with
http://www.youtube.com/watch?v=lI6BgvEpTWk
$250 SHIPPED to you!
2) InlinePRO 550cc saturated injectors
Does not require a resistor box!
These are good for around 350-400whp if I recall correctly, and snap right into your OBD1 clips no problem!
I want 150 shipped for these injectors
3) InlinePRO intake manifold
I aquired this in a turbo kit that I recently purchased, and while from what I gather it is a good Intake manifold, it is not for me.
I did find one instance of this manifold being used on honda-tech, where the motor was used in Matt Kellers drag car where it made into the 800whp range- Just proof that this thing can flow quite a bit of air lol
Anyways I called up InlinePRO, and these are discontinued and he stated that they sell used for 5-600 dollars. I have gathered information that new they were 1100 dollars-
They feature a huge throttle body inlet, that can be port matched to whatever size you need (Luckily this one hasnt been matched yet, so its a blank canvas for you)
The inside of it looks beautiful- check out the pictures!
I think that 500 dollars shipped is a fair price- Shoot offers though!
4) B series Valvecover
Pretty clean!
35 dollars plus shipping-
60 ttrim compressor, 83 turbine according to my calculations (I measured everything)
Shaft spins free, but as with any used turbo, a rebuild would not hurt ya know?
Very little shaft play( Definately within spec)
I even took a video of it- check it out so you can get a better picture of what you are dealing with
http://www.youtube.com/watch?v=lI6BgvEpTWk
$250 SHIPPED to you!
2) InlinePRO 550cc saturated injectors
Does not require a resistor box!
These are good for around 350-400whp if I recall correctly, and snap right into your OBD1 clips no problem!
I want 150 shipped for these injectors
3) InlinePRO intake manifold
I aquired this in a turbo kit that I recently purchased, and while from what I gather it is a good Intake manifold, it is not for me.
I did find one instance of this manifold being used on honda-tech, where the motor was used in Matt Kellers drag car where it made into the 800whp range- Just proof that this thing can flow quite a bit of air lol
Anyways I called up InlinePRO, and these are discontinued and he stated that they sell used for 5-600 dollars. I have gathered information that new they were 1100 dollars-
They feature a huge throttle body inlet, that can be port matched to whatever size you need (Luckily this one hasnt been matched yet, so its a blank canvas for you)
The inside of it looks beautiful- check out the pictures!
I think that 500 dollars shipped is a fair price- Shoot offers though!
4) B series Valvecover
Pretty clean!
35 dollars plus shipping-
Thread
Thread Starter
Forum
Replies
Last Post
ebp_em1
Engine / Exhaust / Drivetrain
10
12-31-2009 03:32 PM
civicryda95
Engine / Exhaust / Drivetrain
1
03-02-2009 02:03 PM
jessetoedtman
Engine / Exhaust / Drivetrain
0
01-20-2009 12:49 PM