FS: Subaru STi and WRX parts - exhaust, dp, up-pipe, FMIC, UTEC, intake, inlet, etc.
#1
Yup, jolly poopbuggy
Thread Starter
Join Date: Nov 2002
Location: Hampton, VA
Posts: 15,599
Likes: 0
Received 0 Likes
on
0 Posts
FS: Subaru STi and WRX parts - exhaust, dp, up-pipe, FMIC, UTEC, intake, inlet, etc.
Name: Corey
Contact: this thread or PM
Location: Newport News, VA
Price: OBO - see below
Most of these items will fit a 2002-2007 WRX or STi. They came off my STi and have literally ONE minute of run-time on them. The car had an engine installed in it when the new parts were installed and the engine ended up being bad (spun rod bearing). I purchased all of these parts new. I'd rather not ship these items. If I do ship, purchaser will pay shipping. I also accept PayPal, but the purchaser will pay the fees.
Items:
Contact: this thread or PM
Location: Newport News, VA
Price: OBO - see below
Most of these items will fit a 2002-2007 WRX or STi. They came off my STi and have literally ONE minute of run-time on them. The car had an engine installed in it when the new parts were installed and the engine ended up being bad (spun rod bearing). I purchased all of these parts new. I'd rather not ship these items. If I do ship, purchaser will pay shipping. I also accept PayPal, but the purchaser will pay the fees.
Items:
- Fujitsubo Legalis R exhaust - $500
- Turbo XS up-pipe (with flex joint) - $125
- XS power FMIC with HKS SSQV Bov flange (and Limited Edition black SSQV BOV) - SOLD
- Gruppe S equal length header - SOLD
- Invida downpipe with divorced bell mouth (Has dent on underside from car being slammed. This is the only part that isn't one minute old.) - $175
- Turbo XS Utec - $200
- ACT street clutch kit w/full face sprung disk - $500
- ACT Streetlight flywheel (15 lbs) - $250
- APS 70mm Cold Air Intake - $200
- Gimmick Motorsports silicone turbo inlet (red) - $120
- Race Comp Engineering Sway bars (Front and Rear - these bars are bright green as I was the demo car for Race Comp Engineering) - SOLD
- Kart Boy end links (front and rear) - SOLD
- Factory STi Diffuser with Cusco mounting bar - SOLD
Last edited by Corey; 06-05-2010 at 09:52 AM.
#6
Yup, jolly poopbuggy
Thread Starter
Join Date: Nov 2002
Location: Hampton, VA
Posts: 15,599
Likes: 0
Received 0 Likes
on
0 Posts
Re: FS: Subaru STi and WRX parts - exhaust, dp, up-pipe, FMIC, UTEC, intake, inlet, e
#7
Re: FS: Subaru STi and WRX parts - exhaust, dp, up-pipe, FMIC, UTEC, intake, inlet, e
i got an 06 wrx will the fronts work at all? i think they will. my car came with aluminum lca's
#10
Yup, jolly poopbuggy
Thread Starter
Join Date: Nov 2002
Location: Hampton, VA
Posts: 15,599
Likes: 0
Received 0 Likes
on
0 Posts
Re: FS: Subaru STi and WRX parts - exhaust, dp, up-pipe, FMIC, UTEC, intake, inlet, e
Hmm. I'm not sure. I looked on KB's webpage and it's hard to tell because they show two types of end links. The part number and pictures are correct, but again, I don't know for sure.