DSM PARTOUT 1g, built motor, trans,precision injectors..etc
12-25-2009, 08:38 PM
#1
DSMs ruined my life!
Thread Starter
Join Date: May 2005
Posts: 571
Likes: 0
Received 0 Likes
on
0 Posts
DSM PARTOUT 1g, built motor, trans,precision injectors..etc
[B]EVERYTHINGS SOLD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!![/B]
UPDATE!!! I STILL HAVENT PULLED THE MOTOR OUT YET, IF U WANTED THE CAR AS IS MEANING ALL U NEED IS A TURBO KIT AND TO FINISH INSTALLING THE NEW WIRING HARNESS I GOT FOR IT, U HAVE A 9 SECOND CAR READY TO GO!!!!
Parting out my 1g dsm, still available is my fully built motor with 2k miles on it
consider trades on eg hatch or coupe, must be manuel.
JE 9:1 Pistons, Eagle Rods, Knife Edged Crank, full blueprint and balance, arp everything, 5 angle valve job, mild port work, Rev Valves with duel valve springs and retainers, comp 272 cam package, have receipts for it, gotta check to see if i missed anything but that pretty much sums it up, motor was built in florida by a very reputable dsm shop, machine work was done by the machine shop next door to them. This build cost over $4600 to have done, will sell for $2k.
also have a jdm vr4 trans available as well as a act 2600 clutch/flywheel combo, dont wanna sell this until either the trans or motor sells first. $400 for trans, will sell clutch after trans sells.
1200cc precision injectors, have about 1 total mile on them considered brand new, paid $340 for them will sell for $280.
5 bar map sensor considered brand new $100.
eprom ecu, $60 (SOLD)
jdm 6 bolt cams, $60
clean 90 gsx awd shell, included is a fresh uncut interior and engine wiring harness UNCUT (process of putting it, dash is removed), comes with 98 gsx wheels (chrome ones), has kyb shocks with intrix springs, has been painted a dark red color, overall pretty clean no rust, will include a 3" custom exhaust with it
$700
UPDATE!!! I STILL HAVENT PULLED THE MOTOR OUT YET, IF U WANTED THE CAR AS IS MEANING ALL U NEED IS A TURBO KIT AND TO FINISH INSTALLING THE NEW WIRING HARNESS I GOT FOR IT, U HAVE A 9 SECOND CAR READY TO GO!!!!
Parting out my 1g dsm, still available is my fully built motor with 2k miles on it
consider trades on eg hatch or coupe, must be manuel.
JE 9:1 Pistons, Eagle Rods, Knife Edged Crank, full blueprint and balance, arp everything, 5 angle valve job, mild port work, Rev Valves with duel valve springs and retainers, comp 272 cam package, have receipts for it, gotta check to see if i missed anything but that pretty much sums it up, motor was built in florida by a very reputable dsm shop, machine work was done by the machine shop next door to them. This build cost over $4600 to have done, will sell for $2k.
also have a jdm vr4 trans available as well as a act 2600 clutch/flywheel combo, dont wanna sell this until either the trans or motor sells first. $400 for trans, will sell clutch after trans sells.
1200cc precision injectors, have about 1 total mile on them considered brand new, paid $340 for them will sell for $280.
5 bar map sensor considered brand new $100.
eprom ecu, $60 (SOLD)
jdm 6 bolt cams, $60
clean 90 gsx awd shell, included is a fresh uncut interior and engine wiring harness UNCUT (process of putting it, dash is removed), comes with 98 gsx wheels (chrome ones), has kyb shocks with intrix springs, has been painted a dark red color, overall pretty clean no rust, will include a 3" custom exhaust with it
$700
Last edited by DJsilkyjr; 03-03-2010 at 03:18 PM.
