Built LSVTEC, Fresh GSR Head, Forged internals, GSR trans, Full B to D swap
#1
Registered Member
Thread Starter
Join Date: Sep 2009
Location: Hoco
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
Built LSVTEC, Fresh GSR Head, Forged internals, GSR trans, Full B to D swap
Name: Killian
Location: Howard County (Columbia, Elkridge, Ellicott City) MD
Means of contact: killianj.hartson@hotmail.com or 301-801-5418
Price: $2700 obo
Description: I am posting to see if there is any interest in my project, or trading for a different car (running car lol). I am interested in 240's, nissan, datsun, etc
No expense was spared in this build. Almost all parts were new
-B18b1 block
-Bored and dipped
-Crank balanced and polished
-Line bore performed
-Arp Main studs
-Eagle H beam forged rods
-Cp 9.0:1 forged pistons
-Full rotating assembly lightened and balanced to over 10k
-Balanced and lightened flywheel
-Oem gsr oil pump
-Oem gsr water pump
-ARP headstuds
-Cometic head gasket
-GSR distributor
-B18c1 head
-Ferrera valves and retainers
-Fullrace lsvtec kit
-ARP rod bolts
-oem tensioner
-oem timing belt
-Edelbrock victor x intake manifold
-countless new gaskets
-stock gsr intake manifold
-fx300 competition clutch (new)
-gsr trans
-gsr shift linkage
-two sets of b series mounts (ebay and oem Si motor mounts)
-tons of oem honda motors bolts/nuts/studs for mounts
-gsr wire harness
-d series vtec harness
-gsr ecu
-AEM cam gears
-MSD Digital sci ignition
-MSD ss blaster coil
-MSD distributor cap
-many other pieces of hardware included
compression is approximately 9.2:1 great for boosting, and probably adequate for n/a as well.
All that's missing is a header, and that will be up to the buyer (wether they boost it or run it n/a for whatever reason), some coolant hoses, radiator, passenger headlight, and it'll need a passenger caliper.
Black Ek sedan, 1997, 100k on body, ground control springs, ls mesh wheels, some ebay exhaust, dent in trunk and in drivers side fender, overall a pretty damn good shell, decent interior.
2700 $ obo any questions just shoot them via email.
Location: Howard County (Columbia, Elkridge, Ellicott City) MD
Means of contact: killianj.hartson@hotmail.com or 301-801-5418
Price: $2700 obo
Description: I am posting to see if there is any interest in my project, or trading for a different car (running car lol). I am interested in 240's, nissan, datsun, etc
No expense was spared in this build. Almost all parts were new
-B18b1 block
-Bored and dipped
-Crank balanced and polished
-Line bore performed
-Arp Main studs
-Eagle H beam forged rods
-Cp 9.0:1 forged pistons
-Full rotating assembly lightened and balanced to over 10k
-Balanced and lightened flywheel
-Oem gsr oil pump
-Oem gsr water pump
-ARP headstuds
-Cometic head gasket
-GSR distributor
-B18c1 head
-Ferrera valves and retainers
-Fullrace lsvtec kit
-ARP rod bolts
-oem tensioner
-oem timing belt
-Edelbrock victor x intake manifold
-countless new gaskets
-stock gsr intake manifold
-fx300 competition clutch (new)
-gsr trans
-gsr shift linkage
-two sets of b series mounts (ebay and oem Si motor mounts)
-tons of oem honda motors bolts/nuts/studs for mounts
-gsr wire harness
-d series vtec harness
-gsr ecu
-AEM cam gears
-MSD Digital sci ignition
-MSD ss blaster coil
-MSD distributor cap
-many other pieces of hardware included
compression is approximately 9.2:1 great for boosting, and probably adequate for n/a as well.
All that's missing is a header, and that will be up to the buyer (wether they boost it or run it n/a for whatever reason), some coolant hoses, radiator, passenger headlight, and it'll need a passenger caliper.
Black Ek sedan, 1997, 100k on body, ground control springs, ls mesh wheels, some ebay exhaust, dent in trunk and in drivers side fender, overall a pretty damn good shell, decent interior.
2700 $ obo any questions just shoot them via email.
Last edited by BullittKid08; 02-17-2011 at 01:41 PM.
Thread
Thread Starter
Forum
Replies
Last Post
BullittKid08
Engine / Exhaust / Drivetrain
5
02-17-2011 06:08 AM
wzexs
Engine / Exhaust / Drivetrain
16
06-30-2010 07:58 AM