machineshop quote
#1
Moderator
Thread Starter
Join Date: Apr 2003
Location: Newport News
Posts: 5,231
Likes: 0
Received 0 Likes
on
0 Posts
machineshop quote
1989 JDM B16A1 Rebuild
headwork
Port Polish head / .30 off head / angle 3 valve job
-$500
block work
milling/replace stuff/valves ground/boring (how much to bore tho)
- $500
Balance Engine
- $175
------------------------
parts: I can buy on my own or ill let him replace the stuff to stock parts
What pistons or stock?
What rods or stock?
What kind of gasket kit?
ARP HEADBOLTS!
FLYWHEEL:
What should I do about this? Get it resurfaced or buy a lighen one? Does a lighen one really matter?
headwork
Port Polish head / .30 off head / angle 3 valve job
-$500
block work
milling/replace stuff/valves ground/boring (how much to bore tho)
- $500
Balance Engine
- $175
------------------------
parts: I can buy on my own or ill let him replace the stuff to stock parts
What pistons or stock?
What rods or stock?
What kind of gasket kit?
ARP HEADBOLTS!
FLYWHEEL:
What should I do about this? Get it resurfaced or buy a lighen one? Does a lighen one really matter?
#4
in all honesty from what I have read/heard and seen if you want a damned good port and polish job, Steen racing kicks ass, that guy loves to port and polish, of course you would need to send your block and everything else to get all the other work done, but If I were you I would go with steen for your porting and polishing needs then someone else to bore your block, and they will only bore out to the size of the pistons you plan on putting in, as far as everything else, I used to go to Performance Unlimited, but after they screwed up my Crank from the turning they did I'm a little skeptical about them, but they did a kick ass job on my block, and pressing my pistons in and reconditioning my rods
just my opinion plus they are all fairly reasonable
just my opinion plus they are all fairly reasonable
#5
Moderator
Thread Starter
Join Date: Apr 2003
Location: Newport News
Posts: 5,231
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by Volkswagen
DO NOT GO TO APPLES.....they screwed my friend over.....SPEND YOUR MONEY AT A BETTER SHOP. ABACUS RACING i heard was pretty good.
-pat
DO NOT GO TO APPLES.....they screwed my friend over.....SPEND YOUR MONEY AT A BETTER SHOP. ABACUS RACING i heard was pretty good.
-pat
#9
Re: machineshop quote
Originally posted by Chezkers
1989 JDM B16A1 Rebuild
headwork
Port Polish head / .30 off head / angle 3 valve job
-$500
block work
milling/replace stuff/valves ground/boring (how much to bore tho)
- $500
Balance Engine
- $175
------------------------
parts: I can buy on my own or ill let him replace the stuff to stock parts
What pistons or stock?
What rods or stock?
What kind of gasket kit?
ARP HEADBOLTS!
FLYWHEEL:
What should I do about this? Get it resurfaced or buy a lighen one? Does a lighen one really matter?
1989 JDM B16A1 Rebuild
headwork
Port Polish head / .30 off head / angle 3 valve job
-$500
block work
milling/replace stuff/valves ground/boring (how much to bore tho)
- $500
Balance Engine
- $175
------------------------
parts: I can buy on my own or ill let him replace the stuff to stock parts
What pistons or stock?
What rods or stock?
What kind of gasket kit?
ARP HEADBOLTS!
FLYWHEEL:
What should I do about this? Get it resurfaced or buy a lighen one? Does a lighen one really matter?